Oracle Sun Netra X4270 Service Manual Download Page 57

Page: 57 / 238

Configure SP LAN Settings

On the Trusted Computing screen, confirm that the TCG/TPM Support setting is set to

Yes

and the TPM Enabled/Disable Status is set to

Enabled

Press the F10 key to exit BIOS.

Related Information

■

“Access the BIOS Setup Utility Menus” on page 46

■

“Exit the BIOS Setup Utility” on page 70

■

Microsoft???s Windows Trusted Platform Module Management documentation

Configure SP LAN Settings

You can assign an IP address for the server SP from the BIOS Setup utility on the IPMI LAN

configuration menu. Alternatively, you can also specify the LAN settings for the SP using

Using the BIOS Setup Utility

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands