Oracle Sun Netra X4270 Service Manual Download Page 46

Page: 46 / 238

BIOS Setup Utility Hot Keys

■

“Understanding BIOS Setup Screens” on page 62

BIOS Setup Utility Hot Keys

The following table provides a description of the BIOS Setup utility hot keys and the

corresponding serial connection key combinations.

ILOM Remote

Console Keys

Serial Connection Hot Key

Combinations

Function

Ctrl+Q (Press and hold the Ctrl

key and type Q)

Access the BIOS Setup utility if there is an error during the

boot process. Also, access the help menu from any BIOS

menu.

Ctrl+E

Enter BIOS Setup utility while the system is performing the

power-on self test (POST)

Ctrl+D

Discard changes and exit BIOS Setup utility

Ctrl+P

Selects the BBS Popup menu, which allows you to select a

boot device

Ctrl+O

Load optimal BIOS defaults

F10

Ctrl+S

Save changes and exit

F12

Ctrl+N

Boot the server from the network (PXE boot)

Related Information

■

“Access the BIOS Setup Utility Menus” on page 46

■

“Exit the BIOS Setup Utility” on page 70

Access the BIOS Setup Utility Menus

You can access BIOS Setup utility screens from the following interfaces:

■

Use a USB keyboard, mouse, and VGA monitor connected directly to the server.

■

Use a terminal (or terminal emulator connected to a computer) through the serial port on the

back panel of the server.

■

Connect to the server using the ILOM Remote Console.

Note -

The BIOS Setup utility data is stored in the system???s battery-backed CMOS RAM. If

the data becomes invalid, the BIOS settings will return to their default, optimal values.

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands