Oracle Sun Netra X4270 Service Manual Download Page 53

Page: 53 / 238

Configure TPM Support

Configure TPM Support

If you intend to use the Windows 2008 TPM feature set, you must configure the server to

support this feature.

Note -

TPM enables you to administer the TPM security hardware in your server. For additional

information about implementing this feature, refer to the Windows Trusted Platform Module

Management documentation provided by Microsoft.

Access the BIOS Setup utility menus.

For instructions, see

“Access the BIOS Setup Utility Menus” on page 46

From the BIOS Main menu screen, select Advanced.

From the Advanced Settings screen, select Trusted Computing.

Using the BIOS Setup Utility

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands