manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 52

Set Watchdog Timers

■

Disabled – Watchdog timer disabled

5.

Set one or both Watchdog timers and set the timeout durations in minutes.

■

SP BIOS Watchdog timer – The SP will perform the selected timer action if the BIOS hangs

or crashes during POST once it reaches the timeout duration.

■

SP OS Watchdog timer – The SP will perform the selected timer action if the Watchdog

timer is not restarted by an OS application before the timer reaches its timeout duration.

6.

Press the F10 key to save the changes and exit BIOS utility.

Alternately, you can select the Exit screen, then select Save Changes and Exit.

Related Information

■

“Access the BIOS Setup Utility Menus” on page 46

■

“Exit the BIOS Setup Utility” on page 70

52

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands