Oracle Sun Netra X4270 Service Manual Download Page 172

Page: 172 / 238

Install the Motherboard Assembly

10.

Remove the motherboard assembly from the chassis.

11.

Place the motherboard assembly aside on an antistatic mat.

Related Information

■

“System Components” on page 25

■

“Field-Replaceable Units” on page 27

■

“Install the Motherboard Assembly” on page 172

Install the Motherboard Assembly

Remove the replacement motherboard assembly from its packaging and place it

on an antistatic mat.

Lower the left edge of the motherboard assembly into the chassis, then the

entire board, and while slightly elevated, slide the motherboard assembly to the

back of the chassis.

172

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands