Oracle Sun Netra X4270 Service Manual Download Page 158

Page: 158 / 238

Remove the Battery

Caution -

Ensure that all power is removed from the server before removing or installing

the battery. You must disconnect the power cables from the system before performing this

procedure.

■

“Remove the Battery” on page 158

■

“Install the Battery” on page 159

Related Information

■

“Replacing DIMMs” on page 132

■

“Reset the BIOS Password and Clear the CMOS NVRAM” on page 177

Remove the Battery

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Remove the PCI mezzanine and place it on an antistatic mat.

See

“Remove the PCI Mezzanine” on page 102

To remove the battery, place your finger between the battery and side wall of the

server chassis and push the battery away from the side wall.

158

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands