manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 144

Remove a Flash Module

Caution - 

Disconnect all power cables from the server prior to removing or installing a flash

module.

■

“Remove a Flash Module” on page 144

■

“Install a Flash Module” on page 146

Remove a Flash Module

1.

Prepare the server for service.

See 

“Preparing the Server for Component Replacement” on page 75

.

2.

Remove the PCI mezzanine and place it on an antistatic mat.

See 

“Remove the PCI Mezzanine” on page 102

.

3.

Locate the installed flash modules on the motherboard in PCIe2 slot 0.

4.

Identify the faulty flash module by pressing the Fault Remind button on the

motherboard and viewing the flash module fault and power LEDs.

144

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands