manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 118

Remove the SAS Controller HBA

7.

Return the server to operation.

See 

“Returning Server to Operation” on page 211

.

8.

Connect any external cable to the PCIe2 card.

Refer to your PCIe2 card documentation for more information.

Related Information

■

“PCIe2 Slot Characteristics” on page 112

■

“PCI Mezzanine Auxiliary Power Connector” on page 114

■

“Remove PCIe2 Cards From Slots 4 and 5” on page 115

Replacing the SAS Controller HBA

These topics describe how to remove and install the SAS controller HBA. Refer to the SAS

controller HBA documentation for complete cabling and software information.

■

“Remove the SAS Controller HBA” on page 118

■

“Install the SAS Controller HBA” on page 120

Related Information

■

“Replacing PCIe2 Cards in Slots 4 and 5” on page 115

■

“Replacing Lower PCIe2 Cards” on page 123

Remove the SAS Controller HBA

1.

Prepare the server for service.

See 

“Preparing the Server for Component Replacement” on page 75

.

2.

Locate the SAS controller HBA on the PCI mezzanine.

The HBA is installed in the right-most slot on the PCI mezzanine.

118

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands