manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 83

Servicing Power Supplies

The server has redundant hot-serviceable power supplies. You can remove and replace a power

supply without shutting the server down, provided that the other power supply is online and

working.

For information about power configuration policies, refer to 

Servers Administration

 and the

Oracle ILOM documentation.

These topics describe how to service power supply modules.

■

“Power Supply LEDs” on page 83

■

“Determine Which Power Supply Is Faulty” on page 85

■

“Remove a Power Supply” on page 85

■

“Install a Power Supply” on page 86

■

“Verify a Power Supply” on page 88

Related Information

■

“Servicing the PS Backplane” on page 165

Power Supply LEDs

Each power supply has LEDs that indicate its state.

Servicing Power Supplies

83

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands