manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 77

Determine Which Fan Module Is Faulty

Determine Which Fan Module Is Faulty

Check to see if any of the following LEDs are lit when a fan module fault is

detected.

■

Service Action Required LEDs on the front and rear panels.

■

Fan Module (FAN) Fault LED on the front panel.

■

Fan Module Fault LED on or adjacent to the faulty fan module.

Note - 

The server Overtemp LED might also light if a fan module fault causes an increase in

server operating temperature.

Related Information

■

“Front Panel Components (Service)” on page 13

■

“Rear Panel Components (Service)” on page 15

■

“Extend the Server to the Service Position” on page 55

■

“Remove a Fan Module” on page 77

■

“Detecting and Managing Faults” on page 27

Remove a Fan Module

This is a hot-service procedure that can be performed by a customer while the server is running.

Caution - 

While the fan modules provide some cooling redundancy, if a fan module fails,

replace it as soon as possible to maintain server availability. When you remove one of the fan

modules, you must replace it within 30 seconds to prevent overheating of the server.

1.

Prepare for servicing.

See 

“Preparing for Service” on page 45

.

2.

Identify the faulty fan module with a corresponding Service Required LED.

The Service Action Required LEDs are located on the fan module as shown in 

“Determine

Which Fan Module Is Faulty” on page 77

.

3.

Using your thumb and forefinger, grasp the handle on the fan module and lift it

out of the server.

Servicing Fan Modules

77

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands