Oracle SPARC T8-2 Service Manual Download Page 172

Page: 172 / 188

Replace the Top Cover

Replace the Top Cover

Place the top cover on the chassis (panel 1).

A metal air baffle is attached to the rear inside surface of the top cover. When you place the top

cover on the server, ensure that the air baffle does not catch on anything inside the server.

Set the cover down so that it is about 1 inch (2.5 cm) forward of the rear of the server.

Slide the top cover toward the rear of the chassis until the rear cover lip engages

with the rear of the chassis.

Close the top cover by pressing down firmly on the cover with both hands, on

the two locations highlighted in green marked "Push here to latch", until both

latches engage.

Caution -

Failure to completely secure the top cover may cause the server to malfunction.

Return the server to its normal operating position.

See

“Return the Server to the Normal Operating Position” on page 173

Related Information

■

“Remove the Top Cover” on page 60

172

SPARC T8-2 Server Service Manual • June 2019

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands