Oracle SG-SAS6-INT-Z Installation Manual Download Page 44

Page: 44 / 80

To Prepare to Use the BIOS Configuration Utility

Using the BIOS Configuration Utility (Legacy BIOS

Booting) to Create a Bootable Drive (x86)

This section describes how to use the BIOS Configuration utility to set up a drive on an x86

system prior to installing an OS. You can then use the drive as your boot drive upon which to

install the OS. This section contains the following topics:

■

“To Prepare to Use the BIOS Configuration Utility” on page 44

■

“To Create a RAID Volume With the BIOS Configuration Utility (x86)” on page 47

To Prepare to Use the BIOS Configuration Utility

From the Integrated Lights Out Manager (ILOM) software or Video Graphics

Array (VGA) video port, access the system console.

Initiate a system boot.

During the boot process, the BIOS initialization banner lists information about the discovered

SAS adapters and devices that are attached to the discovered HBAs in the system.

Upon seeing the prompt,

Press Ctrl-C to start LSI Corp Configuration

Utility...

, immediately press Ctrl+C to access the LSI Corp Config Utility utility.

The LSI Corp Config Utility menu is displayed (see

Figure 13, “LSI Corp Config Utility

Menu,” on page 45

Sun Storage 6 Gb SAS PCIe HBA, Internal Installation Guide For HBA Models SGX-SAS6-INT-Z and SG-SAS6-INT-Z

• May 2017

Summary of Contents for SG-SAS6-INT-Z

















































































Search results

Summary of Contents for SG-SAS6-INT-Z

Reviews:

Related manuals for SG-SAS6-INT-Z

Brands by name

Popular brands

Oracle SG-SAS6-INT-Z, Installation Manual

Search results

Summary of Contents for SG-SAS6-INT-Z

Reviews:

Related manuals for SG-SAS6-INT-Z

Brands by name

Popular brands