Oracle Netra SPARC S7-2 Service Manual Download

Page: 118 / 258

Determine if the Drive Backplane Is Faulty

Related Information

■

“Determine if the Drive Backplane Is Faulty” on page 118

■

“Preparing for Service” on page 43

■

“Install the Drive Backplane” on page 122

Determine if the Drive Backplane Is Faulty

You must determine if the drive backplane is faulty before you replace it.

Check to see if any Server Service Required LEDs are lit or flashing.

See

“Front Panel Components (Service)” on page 17

In Oracle ILOM, check the health of the storage system.

show /System/Storage

/System/Power
Targets:
Disks
Controllers
Volumes
Expanders
Properties:
health = OK
health_details = -
...
->

Verify that the drive backplane is faulty.

For example, type:

show faulty

Target | Property | Value
--------------------+------------------------+-------------------------------
/SP/faultmgmt/0 | fru | /SYS/DBP
...
->

■

If the drive backplane is faulty, you will see

/SYS/DBP

under the

Value

heading.

■

If a FRU value different from

/SYS/DBP

is displayed, see

“Component Service Task

Reference” on page 47

to identify which component is faulty.

118

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands