Oracle Netra SPARC S7-2 Installation Manual Download

Page: 75 / 102

Assembling and Connecting DC Power Cords

Do not attach the power cords to the power supplies at this time.

Connect a device to the SER MGT port.

See

“Connect a Terminal or Emulator to the SER MGT Port” on page 81

Related Information

■

“Connect the Chassis Ground Wire” on page 72

■

“Rear Panel Components (Installation)” on page 15

■

“Powering On the Server for the First Time” on page 71

Assembling and Connecting DC Power Cords

These topics describe how to assemble DC power cords and apply power.

Step

Description

Links

Build the DC power cords and connect them to

the server.

“Assemble the DC Input Power Cords” on page 76

Connect the chassis ground wire.

“Connect the Chassis Ground Wire” on page 72

Connect the DC power cords to the DC power

source.

“Connect DC Power Source” on page 80

Powering On the Server for the First Time

Summary of Contents for Netra SPARC S7-2







































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Installation Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands