Oracle Netra SPARC S7-2 Installation Manual Download Page 65

Page: 65 / 102

Connect Other Data Cables

Connect a Category 6 (or better) cable from your network switch or hub to

Ethernet port 0 (NET 0) on the rear of the chassis.

(Optional) Connect Category 6 (or better) cables from your network switch or

hub to the remaining Ethernet ports.

Related Information

■

“Available Connections” on page 61

■

“Cable the SP” on page 64

■

“Connect Other Data Cables” on page 65

■

“Identifying Ports” on page 65

■

“Rear Panel Components (Installation)” on page 15

Connect Other Data Cables

If your installation includes optional PCIe cards, USB devices, or alarms, make

the appropriate connections to those devices.

Gather the cables and equipment to make these connections, based on your server options:

■

PCIe cards

— refer to PCIe device documentation

■

USB devices

— see

“USB Ports” on page 69

Related Information

■

“Available Connections” on page 61

■

“Cable the SP” on page 64

■

“Cable the Ethernet Ports” on page 64

■

“Identifying Ports” on page 65

■

“Rear Panel Components (Installation)” on page 15

Identifying Ports

These topics provide connector descriptions and pinouts. See

“Rear Panel Components

(Installation)” on page 15

for the locations of the ports.

■

“SER MGT Port” on page 66

Connecting Cables

Summary of Contents for Netra SPARC S7-2







































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Installation Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands