Oracle Netra SPARC S7-2 Installation Manual Download

Page: 18 / 102

Electrical Specifications

Description

U.S.

Metric

Maximum Width (from bezel front to rear protrusions)

17.52 in.

445 mm

Depth (chassis)

Maximum Depth (from bezel front to rear protrusions)

23.9 in.

25.2 in.

608 mm

640 mm

Weight (fully configured without PCIe cards)

†

47.3 lb

21.5 kg

Minimum service clearance (front)

36 in.

914.4 mm

Minimum service clearance (rear)

36 in.

914.4 mm

Minimum airflow clearance (front)

2 in.

50.8 mm

Minimum airflow clearance (rear)

3 in.

76.2 mm

†

Weight specifications vary based on internal options.

Related Information

■

“Electrical Specifications” on page 18

■

“Input Power Information” on page 19

■

“DC Power Source, Power Connection, and Grounding Requirements” on page 21

■

“Overcurrent Protection Requirements” on page 20

■

“Environmental Requirements” on page 22

■

“Acoustic Noise Emissions” on page 23

■

“Airflow Precautions” on page 24

Electrical Specifications

The values in this table are for the power supplies. Use the online power calculator to determine

the power consumption of a server with your configuration:

http://www.oracle.com/goto/

powercalculators

Parameter

Voltage (nominal)

100-127 VAC (800W max out)

200 to 240 VAC (1200W max out)

-48/-60 VDC (1200W max out)

40-47 VDC (900W max out)

Input current (maximum)

10A (100-127 VAC)

7A (200-240 VAC)

36A max @ -48 VDC bus

28A max @ -60 VDC bus

Frequency (nominal)

50/60 Hz

0 Hz

Netra SPARC S7-2 Server Installation Guide • January 2017

Summary of Contents for Netra SPARC S7-2







































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Installation Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands