Oracle Exalytics In-Memory Machine Page 77 Owner'S Manual Download

Page: 77 / 85

Note:

Starting with Oracle Exalytics Release 1 Patchset 3 (1.0.0.3), the Oracle
Exalytics Configuration Utility patch and the ASR utility are included in
the base image.

Steps 1 through 4 are not applicable for users using Oracle Exalytics
Release 1 Patchset 3 (1.0.0.3) or higher version.

If you are using Oracle Exalytics Release 1 Patchset 3 (1.0.0.3) or higher
version, you must start at step

To download and install the Oracle Exalytics Configuration utility patch and ASR
utility, perform the following actions:

Download and install the Oracle Exalytics Configuration Utility patch (1.0.0.4)
and ASR utility for Oracle Exalytics Release 1, Patchset 1
(

ex_x2-4_config_utils_linux_x86_64.zip

file) from the Oracle Software Delivery

Cloud Web site at the following link:

http://edelivery.oracle.com

Unzip the file into a temporary directory.

The zip file contains the files that are listed in

Table 9-1

Table 9-1 Files in the Oracle Exalytics Configuration Utility Zip File

File Name

Notes

exalytics_configure_network.sh

Oracle Exalytics network configuration script

SUN-HW-TRAP-MIB.mib

ASR (Auto Service Request) on Oracle
Exalytics

bda_mon_hw_asr.pl

ASR mail script on Oracle Exalytics

common_subs.pm

ASR on Oracle Exalytics

setup_asr_ilom.pl

ASR on Oracle Exalytics

Create the following directories:

–

mkdir -p /opt/exalytics

–

mkdir -p /opt/exalytics/asr

Copy the file

exalytics_configure_network.sh

/opt/exalytics/bin

. Copy the

following files to the

/opt/exalytics/asr

directory:

–

bda_mon_hw_asr.pl

–

setup_asr_ilom.pl

–

common_subs.pm

–

SUN-HW-TRAP-MIB.mib

Chapter 9

Before You Begin

9-3

Summary of Contents for Exalytics In-Memory Machine






















































































Search results

Summary of Contents for Exalytics In-Memory Machine

Reviews:

Related manuals for Exalytics In-Memory Machine

Brands by name

Popular brands

Oracle Exalytics In-Memory Machine, Owner'S Manual

Search results

Summary of Contents for Exalytics In-Memory Machine

Reviews:

Related manuals for Exalytics In-Memory Machine

Brands by name

Popular brands