Oracle EXADATA X5-2 Installation Manual Download

Page: 15 / 72

System Specifications

This section provides the specifications for the Oracle Exadata Storage Server X5-2 Extreme

Flash installation.

Description

Links

Review the storage server's physical specifications.

“Physical Specifications” on page 15

Review temperature, humidity, and other

environmental requirements for the storage server.

“Environmental Specifications” on page 16

Review power requirements for the storage server.

“Power Specifications” on page 17

Review space requirements to transport the shipping

cartons.

“Shipping Carton Space Requirements” on page 17

Review the storage server agency compliance

“Agency Compliance” on page 18

Related Information

■

“Storage Server Features and Components” on page 9

Physical Specifications

The following table lists the physical specifications for the Oracle Exadata Storage Server X5-2

Extreme Flash.

TABLE 2

Oracle Exadata Storage Server X5-2 Extreme Flash Physical Specifications

Dimension

Storage Server Specification

Specification

Width

Storage server chassis

44.5 cm (17.5 inches)

Depth

Maximum overall

73.7 cm (29 inches)

Height

2-rack unit (2U) nominal

8.76 cm (3.45 inches)

Weight

Fully populated storage server

29.03 kg (64 lb)

System Specifications

Summary of Contents for EXADATA X5-2









































































Search results

Summary of Contents for EXADATA X5-2

Reviews:

Related manuals for EXADATA X5-2

Brands by name

Popular brands

Oracle EXADATA X5-2, Installation Manual

Search results

Summary of Contents for EXADATA X5-2

Reviews:

Related manuals for EXADATA X5-2

Brands by name

Popular brands