manualshive.com logo in svg

Oracle Acme Packet 3900, Hardware Installation And Maintenance Manual, Page: 49 / 70

Share
Download
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual Download Page 49

    H248 Synchronized             disabled 

    Config Synchronized           true

    Collect Synchronized          disabled

    Radius CDR Synchronized       disabled 

    Rotated CDRs Synchronized     disabled

    Active Peer Address           169.254.2.1

Redundancy Protocol Process (v3):

    State                           Standby

    Health                          100

    Lowest Local Address            169.254.1.2:9090

    1 peer(s) on 2 socket(s):       SML-STIC-39001: v3, Active, 

health=100, max silence=1050

                                    last received from 169.254.2.1 

on wancom2:0

2.

Use the display-current-cfg-version command to verify the configuration version
is the same on both the active and standby nodes.

SBC1# display-current-cfg-version

 Current configuration version is 5

 SBC2# display-current-cfg-version

 Current configuration version is 5

 NETNETSBC2#

Note:

While the two current configuration version numbers on the two systems
do not need to match each other, they MUST match the shared running
configuration version.

3.

Use the display-current-cfg-version command to verify the running configuration
version is the same on both the active and standby nodes.

SBC1# display-running-cfg-version

Running configuration version is 5

SBC2# display-running-cfg-version

Running configuration version is 5

NETNETSBC2#

Note:

While the two running configuration version numbers on the two systems
do not need to match each other, they MUST match the shared current
configuration version.

Chapter 5

Standby State for HA Nodes

5-5

Summary of Contents for Acme Packet 3900







































































Reviews:

No comments