OPTRONIC FSU203 Manual Download

Page: 3 / 10

Edition of

FSU203.411

12.09.2012

Version 1.0

Page 3 of 10

FSU203

Table of Contents

1 Introduction ______________________________________________________ 4

2 Device Assembly _________________________________________________ 4

3 Concept _________________________________________________________ 4

4 Video Signals ____________________________________________________ 5

5 Video Cable ______________________________________________________ 5

6 Buttons _________________________________________________________ 6

7 On Screen Menu __________________________________________________ 6

8 Changing Configuration Settings ____________________________________ 7

8.1 Show or Hide Version Information (Show Version ON/OFF) ___________________ 7

8.2 Store Configuration ____________________________________________________ 7

8.3 Load Default Values____________________________________________________ 8

8.4 Adjust Phase__________________________________________________________ 8

8.5 Adjust Horizontally (Adjust Offset X) ______________________________________ 8

8.6 Adjust Vertically (Adjust Offset Y) ________________________________________ 8

8.7 Adjust Width __________________________________________________________ 8

8.8 Adjust Height _________________________________________________________ 8

8.9 Change Orientation ____________________________________________________ 8

9 Trouble Shooting _________________________________________________ 9

Summary of Contents for FSU203











Search results

Summary of Contents for FSU203

Reviews:

Related manuals for FSU203

Brands by name

Popular brands

OPTRONIC FSU203, Manual

Search results

Summary of Contents for FSU203

Reviews:

Related manuals for FSU203

Brands by name

Popular brands