background image

Place projector mount assembly (

C

) on ceiling as a template and mark the center of the two mounting holes. Make 

sure that the mounting holes are in the center of the wood joist. Drill two 5/32” (4 mm) dia. holes to a minimum 

depth of 2.5” (64 mm). Attach projector mount assembly (

C

) with two #14 x 2.5” (6 mm x 65 mm) wood screws (

H

and two 1/4” flat washers (

G

) as shown in 

figure 2.1

 or 

figure 2.2

 depending on joist orientation. 

Note: 

Mounting slots on projector mount assembly (

C

) allow for 30° (±15°) of swivel adjustment before fully 

securing wood screws.
Tighten wood screws (

H

) using 3/8” (10 mm) socket wrench, phillips screwdriver or 10 mm open end wrench until 

projector mount assembly (

C

) is firmly attached.

Installation To Wood Joist Ceilings

H

H

G

G

2

•  Installer must verify that the supporting surface will safely support the combined load of the equipment and all 

attached hardware and components.

•  Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening 

can damage the screws, greatly reducing their holding power.

•  Never tighten in excess of 80 in. • lb (9 N.M.).
•  Make sure that mounting screws are anchored into the center of the stud. The use of an “edge to edge” stud finder 

is highly recommended.

•  Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations. 

WARNING

ISSUED: 04-20-09  SHEET #: 056-9019-7  09-07-10

Visit the Peerless Web Site at www.peerlessmounts.com 

For customer care call 1-800-865-2112 or 708-865-8870.

3 of 11

FRONT OF 

MOUNT

ARROW ON TOP OF PRO-

JECTOR MOUNT ASSEM-

BLY INDICATES FRONT 

OF MOUNT

WOOD JOIST

WOOD JOIST

C

C

fig. 2.1

fig. 2.2

Summary of Contents for BM-5001U












Reviews: