manualshive.com logo in svg

Optimum B 34 H Vario, Operating Manual

Share
Download
Optimum B 34 H Vario Operating Manual Download Page 45

OPTIMUM

M A S C H I N E N   -   G E R M A N Y

Maintenance

21 / 07 / 2014

Page 45

Maintenance  Upright drill B34 H/ B34 H Vario ; Version 1.0.5



 2

014

US

Used oils must be delivered to a collection centre. Consult your superior if you do not know
where the collection centre is.

6.1

Safety

WARNING!

The consequences of incorrect maintenance and repair work may include:
•

very serious injury to employees working on the machine,

•

damage to the machine.

Only qualified staff should carry out maintenance and repair work on the machine.

6.1.1

Preparation

WARNING!

Only carry out work on the machine if it has been disconnected from the main power sup-
ply.

Position a warning sign.

6.1.2

Restarting

Before restarting run a safety check.



 „Safety check“ on page 11

WARNING!

Before activating the machine, double check that this will not
•

endanger other people,

•

damage the machine.

6.2

Inspection and maintenance

This type and extent of wear depends to a large extent on individual usage and service condi-
tions. 

For this reason, all the intervals are only valid for the authorised conditions

. 

Interval

Where?

What?

How?

start of shift

after each 

maintenance or 

repair operation

Up

ri

ght drill

Examination for outside damages.



 „Safety check“ on page 11

Summary of Contents for B 34 H Vario















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands