Optimum B 34 H Vario Operating Manual Download Page 28

Page: 28 / 78

Assembly

OPTIMUM

M A S C H I N E N - G E R M A N Y

21 / 07 / 2014

Page 28

Assembly Upright drill B34 H/ B34 H Vario ; Version 1.0.5



201

3.7

First use

WARNING!

Risk by using improper workpiece clamping materials or by operating the machine with
inadmissible speed.

Only use the clamping materials (e.g. drill chuck) which had been delivered together with
the machine or as optional equipment offered by OPTIMUM.

Use the working clamping materials only in the provided admissible speed range.

Workpiece clamping materials must only be modified according to the recommendations
of OPTIMUM or of the clamping material manufacturer.

WARNING!

Staff and equipment may be endanged if the upright drill is first used by unexpert staff.

We do not take responsibility for damage caused by incorrect commissioning.



„Qualification of employees“ on page 9

Power supply



Connect the electrical feeds.



Check the fuse protection (fuse) of your electrical supply according to the technical specifica-

tions for the total connected load of the upright drill.

Summary of Contents for B 34 H Vario















































































Search results

Summary of Contents for B 34 H Vario

Reviews:

Related manuals for B 34 H Vario

Brands by name

Popular brands

Optimum B 34 H Vario, Operating Manual

Search results

Summary of Contents for B 34 H Vario

Reviews:

Related manuals for B 34 H Vario

Brands by name

Popular brands