Optima Scale OPD-E Maintenance Manual Download Page 12

                                     

OPTIMA

 

SCALE

 

MANUFACTURING

 

INC.

   

 

 

12 

 
8.  Check  if  the  balance  meets  requirements  on  the  production  notice  and  particular  production 
requirements.   
 
9. Check if components on the packing list are complete and if their types correspond with their 
serial numbers one by one. 

 

Chapter XI: Failure and Maintenance   
 

1. Problem: When the balance is switched on, “P    FAIL” is displayed. 
    Failure analysis: mis-operation, failing to switch off the machine normally or pull out power 
                                supply directly. 
    Solution: Press POWER to switch on and then “0.0000g" is displayed. 

 

2.

 

Problem: Switch on the balance and “P FAIL” is displayed. After you press “POWER”,   

                      the screen display is unchanged, the display is abnormal and the pressing sound is 
                      sent out. 
      Failure analysis and Solution: 
      1) Switch on the balance again and check if the failure has been solved.   
      2) Z80 core is damaged and shall be replaced.   
 
3.

 

Problem: “P FALI 2" is displayed after the balance is switched on. 

      Solution: check zero point and full scale count values. 

 

4. Problem: “+E"/"-E" is displayed after the balance is switched on, and nothing happens when   

            POWER is pressed. 

    Failure analysis and Solution: 
    1) If the original part of the circuit board is damaged: replace Q3/Q4 and 1016E cores. 
    2) Check if there is a scale pan and if the scale pan has been overloaded.   

 

5. Problem: “CAL NO” appears during calibration:   
    Failure analysis: 
 
 
   

1) External calibration balance:

   

 
        A: If a mistake happens when the weight is loaded, F1 100g standard weight shall be loaded. 
 

B: If the zero point count value and the full load count value exceed the scope, check and 
      adjust these count values.   
 

   

2) Internal calibration balance:

   

 

A: The weight interferes with other parts when it is loaded and cannot be loaded in place:   
    disassemble the upper cover plate of the balance, check the action when the weight is   

Summary of Contents for OPD-E















Reviews: