manualshive.com logo in svg

OPTIKON KERATRON ONDA, Installation And Operating Manual

Share
Download
OPTIKON KERATRON ONDA Installation And Operating Manual Download Page 16

Keratron

™

  Onda                                                    Installation and operating manual 

OPTIKON 2000 

Cod. 161401EN

 

5-1

 

2015-03-27 

Rev.C

 

5 

GENERAL INFORMATION 

5.1 

SYSTEM DESCRIPTION 

 

 

Figure5-1 Keratron

™

 Onda 

 

 

The  Keratron

™

  Onda  system  is  a   

topograph  aberrometer

  designed  to  provide 

information  on  the  cornea  by  representing  it  using  the  chromatic  maps  that  are 
typical  of  corneal  topography    (axial  powers,  curvatures,  and  corneal  aberrometry) 
and to provide information on the optical aberrations of the ocular or total wave front.  

The main identifiable elements in the Keratron

™ Onda are shown in Figure5-1. They 

are: 

1.  Power switch 

2. 

7” LCD display  with 

touch-screen

:  

 

allows a live view of the patient’s eye for proper positioning of the 
instrument during the measurement 

  allows the operator to send commands by using a special pen to touch 

virtual cursors and buttons on the screen 

Summary of Contents for KERATRON ONDA












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands