Optiguard sp. z o.o.
ul. Aleksandrowska 6-10, 87-100 Toruń
NIP 956-213-03-91
Phone +48 56
654 71 33
4 / 5
USER MANUAL
Disconnecting protecting sensors:
A protecting sensor can be disconnected from a central unit only when it is disarmed. Disconnecting it in other state will cause an alarm. A central unit is armed and
disarmed only through using assigned USER remote controls.
Disarming:
Aim a USER remote control from a distance of up to 0,5 m at an armed central unit with a green LED (Armed) lit and press the right button. Receiving a signal from the
remote control is indicated with a single acoustic sound. The central unit should change its status to disarmed. The green LED (Armed) will turn off, and the yellow LED
(Disarmed) will turn on. In this state one can change protecting sensors on display without triggering an alarm: disconnect connectors from ports or detach protections.
The central unit remains in the disarmed state only for 1 minute. After that it will arm automatically.
Arming:
Before arming a central unit one has to check whether all sensors are properly connected and attached to a merchandise. Aim a USER remote control from a distance of up
to 0,5 m at a disarmed central unit with a yellow LED (Disarmed) lit and press the left button. Receiving a signal from the remote control is indicated with a single acoustic
sound. The central unit should change its status to armed. The yellow LED (Disarmed) will turn off, and the green LED (Armed) will turn on. In this state the central unit
protects the display and any interference will cause an alarm. There should be no constantly lit red LED in any sensor. Otherwise, the system will not be work properly and
the merchandise will not be protected.
Automatic arming:
The central unit remains in the disarmed state only for 1 minute. After that it will arm automatically. If personnel needs more time for changing the display it has to disarm
the central unit using a remote control every time after its self-arming.
5) WAY OF PROCEEDING IN CASE OF AN ALARM
Alarms of the devices can be turned off only using assigned USER remote controls. In case of an alarm one has to absolutely follow the guidelines communicated by a store
management. Bearing in mind safety of the protected merchandise one has to precisely locate the cause of the alarm and check the security state of protected products.
Way of proceeding in case of an alarm of a central unit:
1. Cancel the acoustic signal through aiming a USER remote control at a central unit and pressing the right button. The acoustic signal should turn off while the central unit
will enter the silent alarm mode indicated by red LEDs. The central unit will remain in the silent alarm mode for 30 sec. After that it will trigger an acoustic alarm once
again. If more time is needed to remove the cause of the alarm then one has to switch it to a silent alarm mode every time after triggering an alarm.
2. Find the protecting sensor which has caused the alarm. You can identify it by the red LED in the sensor blinking every second and red highlight of the proper port in the
central unit.
3. After finding the sensor which has caused the alarm one has to disarm the central unit through aiming a USER remote control at it and pressing the right button again.
The central unit should change its status to disarmed. The red LED (Armed) will turn off while the yellow one (Disarmed) will start blinking.
4. Now one has to find the cause of the alarm of the protecting sensor:
- If a merchandise has been veered or removed from the sensor.
- If a cable or charging cable has been removed/damaged.
- If the sensor has been removed/damaged.
5. Removing the cause:
- One should put the protected merchandise on the sensor while replacing the sticker with a new one.
- Replace the cable or charging cable with new ones in case of a permanent damage.
- Replace the sensor with a new one in case of a permanent damage.
6. After removing the cause of the alarm connect the protecting sensor’s cable to the central unit’s port. Aim the USER remote control again at the central unit and press
the right button. The central unit will turn into the armed mode. The yellow LED (Disarmed) will turn off and the green LED (Armed) will start blinking, whereas the port
which the cable has been connected to will start blinking green, which means that the system works properly.
