Opticon OPI-3601 Specification Manual Download Page 35

Page: 35 / 45

OPI-3601

Specifications Manual

11.3. Other Default

Item

Default Setting

Read mode

Single read

Extended read time

Disable

Buzzer duration

75 ms

Buzzer tone

3 kHz

Startup buzzer

Enable

Buzzer loudness

Loud (70%)

Buzzer timing

Before data transmission

Good read LED indicator duration

200 ms

Stand detection

Disable

Data buffering

Buffered mode

[Data buffering]

Not all output data can be received depending on the host system. Therefore, it is recommended
to use buffered mode for USB-HID and Wedge PS/2 interfaces and Unbuffered mode for RS-
232C and USB-COM interfaces.

Unbuffered mode

Buffered mode (default)

@MENU_OPTO@ZZ@D80@ZZ@OTPO_UNEM@

@MENU_OPTO@ZZ@D81@ZZ@OTPO_UNEM@

[Stand detection]

Enable stand detection

Disable stand detection (default)

@MENU_OPTO@ZZ@*4@ZZ@OTPO_UNEM@

@MENU_OPTO@ZZ@*5@ZZ@OTPO_UNEM@

* Refer to “OPI-3601 User’s Manual” for supported commands.

11.4. RS-232C Default

Item

Default Setting

Baud rate

9600 bps

Parity bits

No parity

Data length

8 bits

Stop bits

1 bit

Handshaking

No handshake

ACK/NAK

ACK/NAK no response

CTS time out

Indefinitely

ACK/NAK time out

1 second

Command header

ESC or STX

Command terminator

CR or ETX

Response to the commands

Disable

Summary of Contents for OPI-3601














































Search results

Summary of Contents for OPI-3601

Reviews:

Related manuals for OPI-3601

Brands by name

Popular brands

Opticon OPI-3601, Specification Manual

Search results

Summary of Contents for OPI-3601

Reviews:

Related manuals for OPI-3601

Brands by name

Popular brands