background image

U

SER

S MANUAL

PHL2700 

TERMINAL

/ IRU2700 

CRADLE

19

Keyboard

27 keys total 
(26 keys user definable)

Keyboard function keys 8 Function keys

Keyboard mode

Alpha/Numeric mode

Programming

Functionality is provided by 
user application. The 
application may be down
loaded from PC via cable, 
com port or IrDA.

Interface RS232:

supported by cradle or 
optional supported by direct 
cable

Interface IrDA

supported on terminal

Transmission speed RS232

1200 - 115200 bps

Transmission speed IrDA

2400 - 115200 bps

6.1.5   

Environmental specifications

Temperature in operation -10 - 40 oC

Temperature in storage -20 - 60 oC 

Humidity in operation

20 - 80 % (non condensing)

Humidity in storage

20 - 90 % (non condensing) 

Ambient fluorescent light rejection

3.000 lux max.

Ambient direct sun light rejection:

50.000 lux max.

Shock drop test

1.5 m drop onto concrete 
surface

Shock vibration test

10 - 50 Hz with 1G for 30 
min, cycle for X,Y,Z.

Protection (dust and moisture, IEC529)

IP 42

6.1.6   

Physical specifications

Dimensions (l x w x d)

177 x 62 x 41 mm

Case material

ABS

Weight

175 g (excl. battery)

Connector RS232

DB9 female

6.1.7  

Regulatory

Laser safety class

IEC825, Class I laserproduct

EMC

EN 550222, EN 55024

6.2.1   

Electrical specifications

Voltage requirement

9 V DC

Battery charging time

8 hours charge

6.2.2   

Functionality

Parity

Odd, Even, None

Interface RS232

supported

Interface RS485

supported

Transmission speed

baudrate: 
1200 - 115200 bps

Transmission modes

half duplex RS232
half duplex RS485

6.2.3   

Environmental specifications

Temperature in operation 0 - 40 oC in operation

Temperature in storage -20 - 60 oC in storage

Humidity in operation

30 - 85 % in operation

Humidity in storage

30 - 90 % in storage

Shock vibration test

10 - 50 Hz with 1G for 30 
min, cycle for X,Y,Z.

6.2.4   

Physical specifications

Dimensions (l x w x d)

150 x 90 x 81 mm 

Case material

ABS

Weight

250 g

Connector RS232

D Sub 9P F

Connector RS485

6 pins modular plug

6.2.5  

Regulatory

EMC

EN 550222, EN 55024

6.2   

SPECIFICATIONS CRADLE

Summary of Contents for IRU 2700

























Reviews: