ON
OFF
SP
STD
ON
OFF
Yellow
Yellow Green
M
L
H
Red Green
Red Green
Red
Red
LOW MIDDLE HIGH
MW RANGE
MW SENSITIVITY
POSITION
STD (Standard)
SP (Special)
FUNCTION
Normally set to this.
Set to this if the sensor
malfunctions frequently.
POSITION
OFF
ON
FUNCTION
Microwave is always transmitted.
Microwave is not transmitted
during disarming mode.
This setting is required only when the MICROWAVE
CONTROL is set. (see “6-G. MICROWAVE
CONTROL”)
When the system is not armed, the MC Terminal can
be used to turn off the MW signal as follows.
When an object is placed close to the lens surface,
for a period of more than 10 seconds then the PIR
Anti-Masking circuit will activate and generate a
trouble signal.
The sensitivity of the anti-masking sensor can be set
to STD or SP.
Anti Masking Trouble LED Indication>>
Yellow blinks (OML-AM).
Yellow and Green LED’s blink (OML-DAM).
Caution>>
Powering down the detector will reset the trouble
output.
The Detection Range changes as follows according
to the combination of the MW RANGE and MW
Sensitivity.
Caution>>
The above is a guide only.
Do not set the MW sensitivity too low. This could
cause false MW failure.
It is important to adjust the range and sensitivity so
that the MW and PIR detection areas are overlapping.
POSITION
ON
OFF
Input to MC Terminal
NO CONNECTION=MW ON
NEGATIVE=MW OFF
NO CONNECTION=MW OFF
NEGATIVE=MW ON
POSITION
LOW
MIDDLE
HIGH
Suitable for site requires greater
sensitivity or long range applications
FUNCTION
Suitable for hostile and narrow area
Suitable for standard applications
6-F
POLARITY
Dip switch
7
Dip switch
6
OML-AM
OML-DAM
OML-ST
OML-AM
OML-DT
OML-DAM
OML-AM
OML-DAM
6-D
ANTI-MASKING SENSITIVITY
6-H
PIR SENSITIVITY
6-G
MICROWAVE CONTROL
PIR
SENSITIVITY
Detector
Penetration
If the microwave detection range is set too wide, it may detect
movements outside of the detection area, resulting in false alarms.
By creating a microwave detection area to synchronize to the PIR
detection area, it achieves higher detection performance and
preventing errors and false alarms.
Short
Long
Dip switch
5
and
MW Sensitivity
6-E
MICROWAVE SENSITIVITY /
RANGE
This function checks the operation of detection ability of PIR and
Microwave. This ensures that the unit is always working correctly.
Caution>>
Powering down the detector will reset the trouble output.
Local self test is controlled by the detector
and runs periodically to test the functionality
of the circuitry.
If the local self test fails, the TROUBLE relay
is activated and LEDs blink as follows:
7-A
LOCAL SELF TEST
7-B
REMOTE SELF TEST
SELF TEST
7
This test may be initiated by the control
panel by applying 0V to the RST terminal.
If the remote self test passes, the ALARM
relay is activated for 5 seconds.
If the test fails, the TROUBLE Relay is
activated and the LEDs will blink (see 7-A).
* This function is available only for PIR part.
When this switch is set to ON the microwave can be
turned ON and OFF from the control panel using the
MC terminal.
* The polarity needs to be set. (see “6-F. POLARITY”)
OML-ST
OML-AM
OML-DT
OML-DAM
OML-ST
OML-AM
OML-DT
OML-DAM
OML-ST
OML-AM
OML-DT
OML-DAM
OML-ST
OML-AM
OML-DT
OML-DAM
OML-ST
OML-AM
OML-DT
OML-DAM
OML-ST
OML-AM
OML-DT
OML-DAM
OML-ST
OML-AM
OML-DT
OML-DAM
7-C
WALK TEST
Keep at least 1 meter away from the
detector and clear of any objects.
Put the power on after the cover is
closed.
1m
1
2
Short
Long
L
5m (16ft.)
10m (33ft.)
M
8m (26ft.)
13m (43ft.)
H
10m (33ft.)
15m (50ft.)
Dip switch
4
