5923780 AUG
2015
MANUFACTURER'S STATEMENT
MANUFACTURER'S STATEMENT
WARNING
Do not wash, disassemble, rebuild or repair the sensor, otherwise
it may cause electric shock or breakdown of the equipment.
Danger of electric shock.
WARNING
CAUTION
NOTE
Disregard of warning may cause the improper operation causing death or serious injury of
a person.
Special attention is required to the section of this symbol.
Disregard of caution may cause the improper operation causing injury of a person or damage to
objects.
NOTE
Read this operation manual carefully before use to ensure proper operation of this product.
Failure to read this operation manual may cause improper operation and may result in serious injury or
death of a person.The meanings of the symbols are as follows.
1. This product is a non-contact switch intended for header mount or wall mount for use on an
automatic sliding door. Do not use for any other applications.
2. When setting the sensor's detection area, make sure that there is no traffic around the installation site.
3. Before turning the power ON, check the wiring to prevent damage or malfunction of equipment connected
to the product.
4. Only use the product as specified in the operation manual provided.
5. Be sure to install and adjust the sensor in accordance with the local laws and standards of the country
in which the product is installed.
6. Before leaving the installation site make sure that the product is operating properly and instruct the building
owner/operator on proper operation of the door and the product.
7.The product settings can only be changed by an installer or service engineer. When changed, the
changed settings and the date shall be registered in the maintenance logbook accompanying the door.
NOTE
The following conditions are not suitable for sensor installation :
- Fog or exhaust emission around the door.
- Wet floor.
- Moving objects or objects that emit light near the detection field.
- Highly reflecting floor or highly reflecting objects around the door.
- Grating floor.
It is required to check the operation manual if this symbol is shown on the product.
1
CAUTION
Risk of getting caught.
Make sure to affix the mounting template as described in the above chart ,
otherwise it can be dangerous since there may be no detection area around
the threshold. Install the sensor as low as possible on the header.
H : Height from the floor to the bottom of the header
Y : Distance between the bottom of the header and the sensor
X : Distance between the door and the mounting surface
(The mounting height is "H + Y".)
Maximum mounting distance (Y)
X
H
Y
Sensor
Door
Header
Floor
X
2.00 (6'7")
2.30 (7'7")
2.50 (8'2")
0
No limit
0.05 (2")
0.20 (8")
0.20 (8")
0.10 (4")
0.20 (8")
0.20 (8")
0.20 (8")
0.15 (6")
0.13 (5")
0.15 (6")
0.19 (7")
0.20 (8")
-
0.12 (5")
0.14 (6")
0.25 (10")
0.30 (12")
-
H
0.20 (8")
-
-
-
-
0.11 (4")
[m (feet,inch)]
1. Affix the mounting template at the desired mounting position.
2. Drill two mounting holes of ø3.4mm (ø1/8").
3. To pass the cable through the header, drill a wiring hole of ø10mm (ø3/8").
4. Remove the mounting template.
5. Remove the housing cover. Fix the sensor to the mounting surface with the two mounting screws.
(When setting the detection area close to the door, mount the sensor according to the chart below.)
NOTE
Make sure not to mount the sensor lower than the bottom of header.
WARNING
Danger of electric shock.
Do not use the sensor without the cover.
When using the cable knockout, install the sensor indoors or use the rain-cover
(Separately available) otherwise electric shock or breakdown of
the sensor may occur.
4
Place the housing cover.
If wiring is to be exposed, break the knockout.
2
3
BLUEZONE AREA
When dipswitch 15 is set to "ON", the BLUEZONE area, that provides extra safety over the threshold, is activated.
In case the BLUEZONE function is not required, set dipswitch 15 to "OFF".
Do not set the 2nd row overlapping the threshold regardless of the setting of dipswitch 15.
BLUEZONE
(1st row)
2nd row
3rd row
BLUEZONE
(1st row)
2nd row
3rd row
INSTALLATION
1.Plug the connector.
2.Supply power to the sensor. Adjust the detection area and set the dipswitches.
(See
ADJUSTMENTS 4. Dipswitch settings
)
NOTE
Make sure to connect the cable correctly to the door controller before turning the power ON.
When turning the power ON or after adjusting the settings, do not enter the detection area for more
than 10 seconds in order to enable the presence detection.
OA-FLEX AIR T
OUTER DIMENSIONS AND PART NAMES
(1) Connector
(2) Mounting holes
(3) Operation indicator
(4) Function switch
(8) Area angle adjustment screws
(9) Area width adjustment screws
(5) FLEX EYE Width angle adjustment screw
(6) FLEX EYE Depth angle adjustment screw
(7) Dipswitches
(10) Detection window
(11) Area adjustment tool
[mm (inch)]
Touchless plate
245(9 10/16
"
)
37(1 7/16
"
)
7.5(5/16
"
)
68(2 11/16
"
)
36(1 7/16
"
)
43(1 11/16
"
)
125(4 15/16
"
)
(1)
(2)
(3)
(9)
(8)
(5)
(6)
(7)
(10)
(11)
(4)
This sensor is designed to detect a hand approaching to a touchless plate as a knowing act activation device.
Please make sure to understand the following working principle.
If FLEX EYE mode is enabled (Dipswitch 14 is set to "ON"), this sensor an activation output when both FLEX EYE
and 2nd to 4th row of detection area detect some objects.
FLEX EYE means an area for the hand detection.
Safety output is designed to be used on door system that enables only while the door is open.
When FLEX EYE is enabled (Dipswitch 14 is set to "ON"), detection area (of 2nd to 6th row) is
safety output area.
BLUEZONE is only activated while Activation output is emitted. When no detection, BLUEZONE is deactivated.
1
2
3
4
5
6
1
2
3
4
5
6
FLEX EYE
1
2
3
4
5
6
WORKING PRINCIPLE
Model
Cover color
Mounting height
Detection area
Detection method
FLEX EYE
angle adjustment
Power supply (*2)
Power consumption
Operation indicator
Activation output
: OA-FLEX AIR T
: Silver / Black
: 2.0m(6'7") to 2.5m(8'2")
: See
DETECTION AREA
: Active infrared reflection(*1)
: Depth : -14° to +2°
Width : ±42°
(7 clicks with 6°every click-Left/Right)
: < 2.5W (< 6VA at AC)
: See
Operation indicator table
Output hold time
Operating temperature
Operating humidity
IP rate
Weight
Accessories
: Approx. 0.5 sec.
Noise level
: < 70dBA
Response time
: < 0.3 sec.
: -20 to +55°C (-4 to 131°F)
: < 80%
: IP54
: 230g (8.1oz)
: 1 Operation manual
2 Mounting screws
1 Mounting template
The specifications herein are subject to change without prior notice due to improvements.
NOTE
*1 : BLUEZONE (1st row), 2nd and 3rd rows have a presence detection function.
*2 : When using this sensor, the sensor has to be connected to a door system which has the SELV circuit.
*3 : Overcurrent protection with less than 2A.
*4 : See
BLUEZONE AREA
SPECIFICATIONS
1 Area adjustment tool
1 Cable 3m(9'10")
Area angle adjustment
Width : ±7°
(2 clicks with 3.5°every click-Left/Right)
: Depth : -8° to +8°
: Form A relay
50V 0.3A Max. (Resistance load)
Safety output
: Opto coupler (NPN)
Voltage / 5 to 50VDC
Current / 100mA Max.
(Resistance load)
Dark current / 600nA Max.
Safety intput
: Opto coupler
Voltage / 5 to 30VDC
Current / 6mA Max. (30VDC)
: 12 to 24VAC ±10% (50 / 60Hz)
12 to 30VDC ±10%
Operation indicator table
1sec.
1sec.
Status
Stand-by (Operation mode)
Set-up
BLUEZONE (1st row) detection (*4)
2nd row detection
3rd row detection
4th-6th row detection
Operation indicator color
Yellow Blinking
Green
Blue
Red Blinking
Red
Orange
Signal saturation
Signal saturation (FLEX EYE)
Sensor failure
Slow Green Blinking
Slow Purple Blinking
Fast Green Blinking
Setting error
Red & Green Blinking
Stand-by (Installation mode)
Yellow
FLEX EYE detection
FLEX EYE & 2nd-4th row detection
Fast Purple Blinking
Purple
Category
Performance level
: 2 (EN ISO 13849-1 : 2008/AC:2009)
: d (EN ISO 13849-1 : 2008/AC:2009)
ESPE
: Type2
(8 × 0.22mm² AWG24) (*3)
ENGLISH
NI-0066-0
Original instructions
To the connector
of the sensor
Power supply
12 to 24VAC±10% /12 to 30VDC±10%
}
1.White
2.Brown
3.Green
4.Yellow
5.Pink (+)
6.Blue (-)
7.Red (+)
8.Black (-)
Safety output
Opto coupler(NPN) / Voltage: 5 to 50VDC
Activation output
Form A relay 50V 0.3A Max.
Safety input
Opto coupler / Voltage: 5 to 30VDC
Before starting the procedure, make sure that the power is turned OFF.
When passing the cable through the hole, do not tear the shield.
otherwise it may cause electric shock or breakdown of the sensor.
WARNING
Danger of electric shock.
COMPLIED STANDARDS
AND EXTRACT FROM EC DECLARATION OF CONFORMITY
Notified Body 0044 : TÜV NORD CERT GmbH, Langemarckstr. 20, 45141, Essen, Germany
EC-type examination certificate No. 44 205 13 099217
For technical document,see European Subsidiary
A. Maekawa
General Manager
OPTEX CO., LTD.
Quality Control Dept.
DIN 18650-1:2010 Chapter 5.7.4 ESPE
EN 12978:2003 +A1:2009
EN ISO 13849-1:2008/AC:2009
EN ISO 13849-2:2012
Machinery Directive 2006/42/EC
EN 16005:2012 Chapter 4.6.8 and Annex C
EMC Directive 2004/108/EC
EN 61496-3:2001 clause 4. 3. 5 and 5. 4. 7. 3
EN 61000-6-2:2005
EN 61000-6-3:2007 +A1:2011
B
C
D
E
F
G
H
I
J
BLUEZONE
(1st row)
2nd row
3rd row
4th row
5th row
6th row
FLEX EYE
A
X
DETECTION AREA
The actual detection area may become smaller depending on the ambient light, the color /
material of the object or the floor as well as the entry speed of the object.
The sensor may not be activated when the entering speed of the object or a person is slower than
50mm / sec. or faster than 1500mm / sec.
NOTE
[ m (feet,inch) ]
Charts show the values in the following
area angle adjustment settings ; Depth : 8°
Width : 0°
: Emitting spots
: Emitting spots
(can be eliminated)
Test conditions required by EN 16005
The values above are those of the
Detection area
when tested referring to the test conditions of EN 16005.
(The emitting area is as shown in
Emitting area
above.)
To comply with EN 16005, make sure that the detection area is within the values of the chart below.
Detection area
A
X
H
J
2.30 (7'7")
2.00 (6'7")
0.24 (9")
0.85 (2'9")
2.01 (6'7")
0.25 (10")
0.91 (2'12")
2.20 (7'3")
2.50 (8'2")
0.23 (9")
0.96 (3'2")
2.44 (8')
Floor :Grey paper
Detection object : EN 16005 CA reference body
Sensitivity : High
Speed of detection object : 50mm / sec.
: Detection Area
Emitting area
B
C
D
E
F
G
H
I
J
A
2.00
2.30
2.50
0.38
0.46
0.50
2.06
2.48
2.69
1.49
1.80
1.95
0.92
1.11
1.20
1.75
2.11
2.29
1.34
1.62
1.76
0.84
1.01
1.09
0.71
0.86
0.94
0.13
(6'7")
(1'3")
(6'9")
(4'11")
(3')
(5'9")
(4'5")
(2'9")
(2'4")
(5") 0.16
(7'7")
(1'6")
(8'2")
(5'11")
(3'8")
(6'11")
(5'4")
(3'4")
(2'10")
(6") 0.17
(8'2")
(1'8")
(8'10")
(6'5")
(3'11")
(7'6")
(5'9")
(3'7")
(3'1")
(7")
FLEX EYE
BLUEZONE
BLUEZONE
FLEX EYE
Knockout
Knockout
NOTE
Do not touch the dipswitches before turning the power ON, otherwise an error occurs.
When changing the settings of dipswitch, see
ADJUSTMENTS 4. Dipswitch settings
ø
83 (
ø
3 4/16
"
)
