background image

14 

USERNAME AND PASSWORD 

*OpenEye IP cameras ship without a default password. 

Username: 

admin 

Note

  

Passwords must be 9-32 characters including at least two elements of the following three: 

digits, letters, and special characters.

 

The 

admin

 user password can be set using the following methods: 

1.

 

OpenEye recorders running Apex 2.1 or newer will automatically set a new unique password 

if: 

 

Connected to an M-Series recorder with a built in PoE switch. 

 

Connected to a network switch through the camera network port and selected then 

added in setup, if a new password has not already been set. 

Note

 

You can set your Default Camera Password under the General Settings page within  

 

Setup > System Settings > General Settings.

 For instructions on defining your unique 

camera password, visit:  

 

https://www.openeye.net/support/faqs/default-camera-password

 

2.

 

Connect to the camera directly through a Web Browser and follow the onscreen prompts. 

3.

 

Use the Network Camera Manager (NCM) Utility. 

Note

  

The NCM Software Manual can be found at https://www.openeye.net/ncm-manual.

 

Note

 

Refer to your Apex recorder manual or quick start guide for instruction on adding cameras.

 

VIEWING A NETWORK CAMERA 

Click 

Load

 in the row of the desired camera.

 

Enter a new Admin password.  

 

Passwords must be 9-32 characters and include at least two of the following three 

elements:  

o

 

Digits 

o

 

Letters 

o

 

Special Characters 

 

All special characters are allowed 

 

 

Summary of Contents for OE-C1012D2













































Reviews: