ChannelPlus model
H636
5 Port Ethernet Switch 10/100 BASE-T
1
2
3
4
5
TM
Power
12-15VDC 300mA
ON - 100Mbps
OFF - 10MBps
ON - Connected
BLINK - Activity
Use crossover cable for link
ChannelPlus model
H636
5 Port Ethernet Switch 10/100 BASE-T
1
2
3
4
5
TM
Power
12-15VDC 300mA
ON - 100Mbps
OFF - 10MBps
ON - Connected
BLINK - Activity
Use crossover cable for link
ChannelPlus model
H636
5 Port Ethernet Switch 10/100 BASE-T
1
2
3
4
5
TM
Power
12-15VDC 300mA
ON - 100Mbps
OFF - 10MBps
ON - Connected
BLINK - Activity
Use crossover cable for link
The H636 10/100Base-T ethernet switch
creates a home network
for two to five computers. “Plug and play” installation is easy when using the
H628 data hub. The H636 is fully IEEE802.3 compliant and has activity LEDs
for network status and speed.
T h e H 6 3 6 r e q u i r e s n o
programming and starts working
at power up with no user
intervention.
ChannelPlus
Fast Ethernet Switch
1
2
3
1) Hook from the top
2) Swing into place
3) Push button to lock
OpenHouse modules attach from the top
tm
ChannelPlus model H616
Telephone Master Hub (4 lines x 6 phones)
Telephone Master Hub (4 lines x 6 phones)
Telephones
From
Telco
From
Telco
RJ31X
Out
Expansion
Ports
Expansion
Ports
R
T
R
T
4
R
T
R
T
3
R
T
R
T
2
R
T
R
T
1
Typical Installation
Expanding the Network
Wiring the H636 Hub
- Use only Category 5 unshielded twisted-pair cable.
- When connecting to an H628 or a network device directly, use
straight through RJ-45 cables.
- Each run to a network device should be less than 100 meters (328
feet).
DECLARATION OF CONFORMITY
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2)
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which if found by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver.
-Connect the equipment to an outlet other than the receiver’s outlet.
-Consult a dealer or an experienced radio/TV technician for assistance.
Power supply
LED Indicators
Network Interface
model number
105-125 VAC
Link/Activity, Speed
Use crossover cable
300mA maximum
15 VDC unregulated
Power
5
350-099
input power
each port
RJ-45 uplink
output voltage
each unit
RJ-45 ports
output current
Environmental
Compliance
operating temperature
IEEE 802.3
0°C to 50°C
100Base-T
Max cable length
CAT-5 (UTP)
100 meters (328 feet)
Specifications: typical @ 25 C ± 5 C
O
O
H636
Ethernet Hub
BASE-T (5 RJ-45 inputs, 1 uplink)
10
+5VDC
ChannelPlus model H628
Data Hub (8 cables, TIA-568A) Category 5 Compliant
H628
Straight-through cable
(H691 or H692)
H636
Ethernet hub
H636
Ethernet hub
Ethernet connections for 4 rooms
}
To data jacks
in remote
wall plates
Uplink
5
4
3
2
1
+5VDC
Using more than one hub
Crossover cable
- Use only Category 5 unshielded twisted-pair cable.
- The cable length between two hubs cannot exceed 100 meters
(328 feet).
- Additional hubs may be used as long as the path between any
two network devices does not exceed four hubs and five cables.
- All hubs used must be powered.
-A crossover cable exchanges the In and Out connections on one
end. This will convert any standard port into a “link” port.
Connecting two H636s or connecting an H636 to most firewalls
will require using a crossover cable.
ChannelPlus model
H636
5 Port Ethernet Switch 10/100 BASE-T
1
2
3
4
5
TM
Power
12-15VDC 300mA
ON - 100Mbps
OFF - 10MBps
ON - Connected
BLINK - Activity
Use crossover cable for link
ON - 100Mbps
OFF - 10Mbps
ON - Connected …
A working device is connected to this port.
BLINK - Activity …
Data is being transmitted or received by this port.
To Internet
Crossover cable
(typical)
Internet gateway
or firewall
H636
Ethernet hub
Crossover cable
LED Indicators
Ethernet switches
The H636
The H636
are superior to ordinary Ethernet hubs in that they
segment the data traffic. Computer A can talk to computer B while computers
C and D also talk. Collisions are eliminated. Throughput is greatly enhanced.
learns the addressing of your network with no programming.
will automatically detect 10 base-T or 100 base-T adaptors on a
port by port basis. The H636 will use the highest possible speed.
