Opel 1900 1973, Service Manual

Page: 49 / 625

2 8 1 9 7 3 O P E L M A N U A L
SYSTEM
DESCRIPTION OPERATION‘:
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R e g u l a t o r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS: (Not Available):
MAINTENANCE AND ADJUSTMENTS:
Alternator Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulator Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAJOR REPAIR:
Alternator Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternator Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternator Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternator Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS:
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
1 D-28
1 D-29
1 D-29
1 D-29
1 D-30
1 D-34
1 D-35
D-35
1 D-35
DESCRIPTION AND OPERATION
ALTERNATOR DESCRIPTION
35 amp alternator is standard equipment on
all 1973 models.
Figure Alternator Installed
The alternating current generator (alternator) is a
continuous-output (even at idle), diode rectified gen-
erator. See Figure
The rotor, which carries the field winding, is
mounted in ball bearings at both ends. Each bearing
has a sealed-in grease supply which eliminates the
need for periodic lubrication. Two brushes and two
slip rings are used. One brush conducts the current
provided by the voltage regulator to one end of the
field coil; the other brush conducts the current from
the other end of the rotating field coil to ground.
The three phase windings are assembled on the
inside of a laminated core that forms the center sec-
tion of the alternator frame. Nine rectifier diodes are
connected to the
windings (three to each phase
lead). The diodes change the alternator AC voltages
to DC voltage coming out of the B positive and the
D positive terminals of the alternator.
If the alternator will not meet output specifications
when supplied with full field current, the
assembly
must be overhauled. If the voltage regulator does not
limit maximum voltage within specifications, adjust
the voltage regulator. If steady voltage regulation,
within specifications, cannot be achieved, the voltage
regulator assembly must be replaced.