background image

   

   Rescue   System   ©Copyright   by   Opale-­‐Paramodels   2012      

   Page   

2

   sur   

9

   

 

Safety Information 

 
 
 
 
 

 
Table of contents

 

1.

 

Kit content……………...................……………………………………………………………………………………………………………………………….4 

2.

 

Getting your Trike M2 ready…..………………………………………………………………………………………..………………………………….5 

3.

 

Parachute assembling…....……..………….………………………………………………………………………………………………………………….8 

4.

 

Parachute folding……………………..……………..……………………………………………………………………………………………………………9 

1. Kit content

 

 

-

 

1x 1.8 m

²

 Rescue parachute, with lines, strap and container  

-

 

1x Drop Pod for the Trike M2 

-

 

1x Main frame carbon fiber plate for the Trike M2 

-

 

1x Carbon fiber plate to hold the triggering servomotor 

-

 

3x screws with washers and nuts 

2. Getting the Trike M2 ready

 

You need first to remove the original main frame plate. Replace it by the carbon fiber one provided in this kit. 
Then, screw the 5 screws back. 

You    should    be    properly    insured    according    to    the    country    regulation    you    are    using    our   
equipment   in.   You   hereby   accept   the   inherent   risk   of   flying   radio-­‐controlled   models.   

   

Using   our   equipment   in   a   bad   way   may   increase   risks.   Neither   Opale-­‐Paramodels   nor   any   other   
seller   will   be   liable   for   any   damage   caused   by   any   accident   whatever   the   circumstances   are.   
The   way   our   equipment   is   used   is   incumbent   upon   the   final   user,   including   towards   the   law

   

 

Summary of Contents for Trike M2










Reviews: