background image

Quick Start Guide

700-0129-203

1

3

5

2

4

6

8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone 

that can be worn or kept by your side all day. 

Since the Safety Phone is a fully-working speaker 

phone capable of two-way communication, you can 

use it to make and receive calls anywhere within the 

range of your home Ooma system. 

Comfortable to wear and programmable with up to 

two speed dial numbers, the Safety Phone gives 

you the peace of mind that your caretaker and loved 

ones are just a button press away. The Safety Phone 

can effectively support your independent lifestyle.

Important Information About the Safety Phone

  Carefully read and follow the instructions in this 

Quick Start Guide, which may also be viewed 

online at:

    

http://www.ooma.com/support/documentation

 

    Do not use the Safety Phone if you cannot 

understand and follow the instructions.

  Use of the Safety Phone requires high-speed 

Internet access and the Ooma Telo device. The 

Safety Phone will not work if either the Internet or 

Ooma Telo are not functioning properly.

  The Safety Phone is intended for indoor use with a 

range of up to 50 meters (164 feet) from the Ooma 

Telo. This range may vary based on factors such 

as home construction and other electrical devices 

and appliances being used in the home.

  The battery in the Safety Phone is not replaceable. 

The expected lifetime of the battery is two years, 

but may vary based on usage.

  Do not use the Safety Phone if you have an 

implanted cardiac pacemaker.

Charging cradle with 

AC 

adapter

Microphone
Status LED
 

Changes color and blinks 

to indicate the status of 

the Safety Phone.

Talk 

Press to place a call, and 

again to end the call.  

Press and hold to power the 

Safety Phone on or off.

Speaker
Volume Up
 

Press to increase earpiece 

or ringer volume. 

Volume Down 

Press to decrease earpiece 

or ringer volume.

Speed Dial Buttons

Charge Phone

Register Phone

Program Speed Dial Online

Quick Reference Guide

Place the Safety Phone on the charging cradle 

and charge for a few minutes until the status 

LED turns purple and you start to hear the Safety 

Phone play two short beeps periodically.
When you are ready to register the phone, take 

it out of the cradle and put it back in. The status 

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma 

device for three seconds to activate registration 

mode. 
The Safety Phone will now register with your 

Ooma system. When the registration process  

is successful, you will hear a long beep.
Continue to charge the Safety Phone for at  

least three hours until the status LED lights up 

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two  

speed dial buttons. 

Step 1

Step 2

Step 3

Ooma Safety Phone with lanyard

BC

Breakway 

connector

WARNING: 

 To avoid injury, 

please review the Important Safety 

Information section on page 11 

before using the Safety Phone.

Operation Instructions

 Powering the Safety Phone on or off

To power the phone on or off, press and hold the 

TALK button until you hear three short beeps.

 

Making an outgoing call

Outgoing calls can be placed to either of the two  

pre-programmed speed dial buttons. Press the 

appropriate button to call the programmed number.

 

Answering a call

Answer incoming calls by pressing the TALK button.

 

Ending a call

To end a call, press the TALK button again while  

on a call. You can also end a call by putting the  

Safety Phone back onto the charging cradle.

 

Adjusting the volume

The speaker volume can be adjusted up by pressing  

the VOLUME UP or VOLUME DOWN button during 

a call. Use the same buttons to adjust the ringer 

volume when the phone is in idle mode.

 

Registering to a new base unit

Register the Safety Phone to a different base unit 

by pressing and holding the VOLUME UP and 

VOLUME DOWN buttons at the same time until the 

status LED toggles between red and blue.

7

Reviews: