background image

-17- 

If the PINCODE is correct the unit replies with a beep. If it is not correct the call 
is disconnected. Call again and try. 

4.

 

Acknowledge the alarm by pressing the buttons 

9#

.  The unit replies with a 

beep.  Hang up the receiver. If the unit replies with two beeps, try again. Also 
alarms from extra relays (Ontech 9010) will be acknowledged. 

 
Acknowledge an alarm with SMS 

1.

 

Send an SMS to the unit with the following message: 

ABCD#9# 

(ABCD is your 

PINCODE). Also alarms from extra relays (Ontech 9010) will be acknowledged. 

Temperatur 

Temperature sensors 

Ontech GSM 9030 will by default use the internal temperature sensor for controlling and 
alarming. The accuracy is +/- 3 degrees C. The internal temperature sensor is also 
affected by the relay. If the relay is activated it will indicate 1-2 degrees higher than 
normal, due to heat produced by the relay. 
 
If you wish higher accuracy (+/- 1) we recommend you to purchase the external 
temperature sensor ”Ontech Temp Sensor 9020_002”. 
 

Installation of external temperature sensor 

The external temperature sensor is connected to the temp sensor contact close to the 
SIM-card holder. In order to make place for the cable you must remove some material 
from the cover on the marked place (where material is made thinner). 
 
If you wish to use the external temperature sensor for controlling the thermostat and 
trigging the temperature alarm you have to program the SIM card for this purpose (see 
page 8).  
Create a new contact and name it EXTTEMP and in the telephone number field write “1”. 
NB. The external temperature sensor is not delivered together with Ontech GSM 9030. It 
is optional.  

Temperature alarm 

Default setting 

If the temperature alarm is turned on the unit will send an alarm if the temperature 
drops below 5 degrees C.  The alarm does not have to be acknowledged but the unit 
will not send another alarm before the temperature has reached at least 6 degrees C. 

Summary of Contents for GSM 9030





































Reviews: