Onkyo TX-NR535, Service Manual

Page: 16 / 80

NOTATION ABOUT ENTERING TEST MODE BY PRESSING BUTTON
In this procedure, the following notations are used to simplify explanation of how to press button.
e.g.-1
[TV/CD] + [ON/STANDBY] → [BD/DVD]
This means "While holding down TV/CD button, press ON/STANDBY button then release both buttons and then press
BD/DVD button".
e.g.-2 [DISPLAY] + [ON/STANDBY] *2 → [DIMMER]
This means "While holding down DISPLAY button, press ON/STANDBY button twice then release both buttons and then press
DIMMER button".
INITIAL SETTING FOR SHIPPING
Initialization of memories.
Do the following operation.
Unplug the power cord from AVR after the FL tube displays "Clear" and AVR goes standby.
[CBL/SAT] + [ON/STANDBY]
CONFIRMATION OF F/W VERSION
to display MMPU version.
to display another F/W version.
<NOTE>
It cannot enter a test mode immediately after power supply ON, please press the Setup key.
1. [DISPLAY] + [ON/STANDBY]
Do the following operation.
2. [TONE+]
M1.03/14307ALN
M1.03/14307ALN
N1.02/14210ALA
O1.00/13Z05AL
Main
DSP
OSD
1. set the volume level to 25 .
3. Press the following button, while "TEST - " is displayed, then each test mode is set.
TEST MODE FOR OPERATION
Do the following operation.
2.
[TV/CD] + [ON/STANDBY]
TEST-_
e.g.
1-00
2-00
3-00
4-00
5-00
6-00
[BD/DVD]
[CBL/SAT]
[STB/DVR]
[GAME]
[PC]
[AUX]
KEY TEST [MEMORY]
IDLING TIMER / Wi-Fi check [TUNING MODE]
FL TEST
[DIMMER]
(RT/PTY/TP)
[ENTER]
FIRMWARE COMBINATION CHECK
Button Button Test Mode Test Mode
In the test mode, (TONE)- button is TEST MODE DOWN and (TONE)+ button is TEST MODE UP.
TEST 1-00 → TEST 1-01 → TEST 1-02 - - - - TEST 2-00
e.g.
CONFIRMATION OF FIRMWARE COMBINATION
Firmware combination can be confirmed the following operation.
In this case, it will be OK if the following result come out on the FL tube after waiting for a few seconds.
[TV/CD] + [ON/STANDBY] → [ENTER]
F/W Set OK
CONFIRMATION OF MAIN CHECKSUM
MAIN Checksum can be confirmed the following operation.
[DISPLAY] + [ON/STANDBY] * 2 → [MEMORY]
Temperature and output voltege can be confirmed the following operation.
CONFIRMATION OF OUTPUT VOLTAGE AND THERMAL SENSOR
[DISPLAY] + [ON/STANDBY] * 2 → [TONE]
Model name and destination can be confirmed the following operation.
[TV/CD] + [ON/STANDBY] → [DIMMER](RT/PTY/TP) → [TONE] *4
CONFIRMATION OF MODEL NAME AND DESTINATION
e.g.
001 042 F:x S:H
Amplifier power
supply voltage condition
H : High-B
L : Low-B
Temparature
of thermal sensor
Voltage
of VOLH port
FAN speed
x: Stop
L: Low speed
H: High speed
e.g.
N R 5 3 5 D x 2 0 0 0
FL DIS Name Destination A B C D
A:Value of AD port of BAND
B:Value of AD port of INIT1
C:Value of AD port of INIT2
D:Value of AD port of INIT3
e.g.
Distination Number Writing Data
TX-NR535 Dx 2000 2000 TX-NR535 Dx N R 5 3 5 D x 2 0 0 0
TX-NR535 xx 8000 8000 TX-NR535 xx N R 5 3 5 x x 8 0 0 0
FL Display
Model Name
CONFIRMATION OF VOLTAGE-DETECTION PROTECTORS.
to the following test mode.
2. AVR automatically tests in the following test sequence. And if it is all OK, Wi-Fi test will begin.
3. If FL tube displays Wi-Fi check mode then voltage-detection protectors test will be completed.
TEST 1-01
Test sequence
(FL+) → (FR-) → (C+) → (SL-) → (SR+)
<NOTE>
Don't connect load nor short speaker terminals.
1-2. [TV/CD] + [ON/STANDBY] → [BD/DVD]
1-1. set the volume level to
25
.
1. Do the following operation.
1-3. [TONE +]
CONFIRMATION OF UPDATE ROUTE.
Once the above mentioned test mode is entered, voltage-detection protectors function is checked automatically first, then update
route check will begin.
If the result of update route check is no problem then Wi-Fi check will begin. If the result is NG then NG message will be shown on
the FL tube.
If FL tube displays Wi-Fi check mode then voltage-detection protectors test and update route check are passed.
to the following test mode.
TEST 1-01
1-2. [TV/CD] + [ON/STANDBY] → [BD/DVD]
1-1. set the volume level to 25 .
1. Do the following operation.
1-3. [TONE +]
CONFIRMATION OF Wi-Fi CONNECTION
1. Setting Wi-Fi routers.
3. Once the above mentioned test mode is entered, voltage-detection protectors function is checked automatically first, then update
route check will begin and then Wi-Fi check will begin.
In Wi-Fi check mode, it connects an access point automatically. Wi-Fi LED flashes during connection.
4. If connection is completed and IP address is successfully acquired, Wi-Fi LED turning lights off and the value of RSSI to an access
point is displayed in dBm.
If the connection is failed, NG is displayed.
If the connection is failed, exit the idling timer mode by pressing the TV/CD button and please try again from step 1.
In case value of RSSI level isn't showed on the FL tube at all past 4 minutes in this timer mode, judge as NG.
TEST 1-01
2. set the following test mode.
02 -55d 01’ 14’’
RSSI(dbm) SSID No Time Counter
e.g.
COMFIRMATION OF ZONE2 DAC ROUTE
1. Connect USB memory or USB storage to AVR front USB port.
3. After being displayed Wi-Fi RSSI level, it will play back wave file from USB storage.
4. Check the wave form that appears L+R and R alternately from the following output terminal.
Output terminal :
ZONE2 LINE OUT
2. set the following test mode.
TEST 1-01
CONFIRMATION OF CURRENT DETECTION PROTECTORS
2. Confirm that relay is not cut off even if you connect the following load A to the following channels one by one.
3. Confirm that relay is cut if you connect the following load B to the following channels one by one.
Channel FL, FR, C, SL and SRch
Load A 3 ohm
Load B 1 ohm
to the following test mode.
TEST 1-09
1-2. [TV/CD] + [ON/STANDBY] → [CBL/SAT]
1-1. set the volume level to
25
.
1. Do the following operation.
1-3. [TONE - ]
CONFIRMATION OF OUTPUT SENSOR
After lighting "FM STEREO" on the FL tube, the following relays break their connections and "FM STEREO" lamp goes off .
Relays RL643 and RL644
to the following test mode.
TEST 1-07
1-2. [TV/CD] + [ON/STANDBY] → [CBL/SAT]
1-1. set the volume level to 25 .
1. Do the following operation.
1-3.
[TONE - ] *2(*3)
TEST 1-08
CONFIRMATION OF KEY OPERATION
2. Confirm each key and master volume operation.
3. If "ON/STANDBY" button is pressed, AVR escapes from this KEY test mode.
Therefor, press the "ON/STANDBY" button, after checking other buttons finished.
to the following test mode.
TEST 1-06
1-2. [TV/CD] + [ON/STANDBY] → [CBL/SAT]
1-1. set the volume level to 25 .
1. Do the following operation.
1-3. [TONE - ] *4
CONFIRMATION OF NETWORK
1. Connect the receiver to the router.
3. Confirm that the AVR's display shows appropriate IP address.
Please wait for about 1 minute after turning on the AVR when using the following test mode.
Connection
Ethernet
cable
ETHERNET connector
to the following test mode.
TEST 1-05
2-2. [TV/CD] + [ON/STANDBY] → [CBL/SAT]
2-1. set the volume level to 25 .
2. Do the following operation.
2-3. [TONE - ] *5
The sound from USB flash device is output from Zone2 PREOUT or Zone2 LINEOUT via Zone2 DAC.
<NOTE> Store only one file (the above mentioned) into the USB flash device to avoid making trouble.
IDLING TIMER ( TEST 1-01)
This mode is used for aging for idling.
Once the following test mode is set, idling timer mode works.
Idling timer mode includes the following functions.
Test mode TEST 1-01
Function Timer
Voltage-detection protector check
F/W update route test
Wi-Fi connection check
Z2 DAC route check by playing USB flash device
WAV file L+Rch and Rch repetition (1sec each)
Once the above test mode is set, AVR's status changes to idling timer mode and voltage-detection protector check automatically begins.
If voltage-detection protector check is all OK, Wi-Fi connection check automatically begins.
Even if one channel of voltage-detection protector check is NG, Wi-Fi connection check doesn't begin.
Refer to CONFIRMATION OF VOLTAGE-DETECTION PROTECTORS (next page).
Refer to CONFIRMATION OF UPDATE ROUTE (next page).
Refer to CONFIRMATION OF Wi-Fi CONNECTION (next page).
Refer to COMFIRMATION OF ZONE2 DAC ROUTE (next page).
TX-NR535 TX-NR535
TX-NR535 TX-NR535
OPERATION CHECK-1 OPERATION CHECK-2
OPERATION CHECK-3 OPERATION CHECK-4