background image

Smart Pro™ © O.A.S. 2011

 13

XI. Filter Maintenance

External Filter Cartridge Cleaning Intervals

When unit is turned off, use compressed air to blow dust off from 

exterior of filter. Hold nozzle at least 6” away from filter pleats*. 

Do not remove bottom dust pan before or during the blow-off 

process! Let dust settle into dust pan. Unclip and dump out dust. 

Filter removal is not required.

*WARNING: A close, direct blast with the compressed air nozzle 

too close to filter, may damage filter media. Always wear safety 

glasses while blowing off filter.

Fan / Blower & Cyclone Outside Placement

Fan / Blower has a TEFC - Totally Enclosed Fan Cooled Motor.

Note: Use steel drum when placed outside.

Before Operation:

Mount system and connect cyclone and dust bin. Make sure dust bin is in place and ductwork is connected 

to inlet before turning on the dust collector.

Electrical Wiring:

Make sure power source matches wire voltage configurations on motor.

Prior to connecting to the power line, check motor plate for proper voltage. 

Motor is pre-wired for counter-clockwise rotation. Fan wheel must rotate 

counter-clockwise if looking down on fan housing.

Use 12 gauge cord for the fan / blowers.

Lubrication:

See pg. 15 for schedule and specifications.

Caution: Rotating Fan Blades! Keep objects clear of outlet.

Do not operate Fan / Blower unless Cyclone and Dust Bin are in place! Motor will overheat!

Caution: Fine dust collected in filter is hazardous to 

your health! Do not breathe!

Shown with 

optional Stand.

Attach the ring terminal on the green 

ground wire from the motor to a bolt on the 

filter plate, under the nut. Then attach the 

alligator clip to the filter cage as shown in 

Fig. 1.

Figure 1

Filter Grounding Wire

5hp Systems 

require a 30 

Amp breaker.

Summary of Contents for Smart Pro XXS200001





















Reviews: