One Stop Systems OSS-PCIe-HIB38-x16-H User Manual Download Page 10

Page: 10 / 12

One Stop Systems

OSS-PCIe-HIB38-x16-H/T

Specifications subject to change without notice

Page 10

PETn3

Lane 3

GND

Ground

GND

Ground

PERp3

Receiver differential pair, Lane 3

RSVD

Reserved

PERn3

PRSNT2#

Hot-Plug presence detect

GND

Ground

GND

Ground

RSVD

Reserved

Notes:

Optional signals that are not implemented are to be left as no connects on the board side connector.

Reserved signals must be left as no connects on the board side connector.

Although support of CWAKE# is optional from the board side connector perspective, an allocated wire is mandated for the cable

assembly.

Board side pin-out on both sides of the Link is identical. The cable assembly incorporates a null modem for the PCIe transmit and

receive pairs.

PCI Express x16 Connector Pin Assignment

Row A, Pin 1

Row B, Pin 19

Summary of Contents for OSS-PCIe-HIB38-x16-H













Search results

Summary of Contents for OSS-PCIe-HIB38-x16-H

Reviews:

Related manuals for OSS-PCIe-HIB38-x16-H

Brands by name

Popular brands

One Stop Systems OSS-PCIe-HIB38-x16-H, User Manual

Search results

Summary of Contents for OSS-PCIe-HIB38-x16-H

Reviews:

Related manuals for OSS-PCIe-HIB38-x16-H

Brands by name

Popular brands