One Stop Gardens 69714 Owner'S Manual & Safety Instructions Download Page 13

Page 13

For technical questions, please call 1-800-444-3353.

Item 69714 

        

Transparent Panel Installation

2A/4A

36

2A

2A

35

32

4A

15

1.  Panel Clips (46) are used to secure the 

Transparent Panels in place on the Greenhouse.   

(See Parts List A.)

Note:

 Remove the protective film from both sides 

of all panels as they are installed.   

After removing the protective film from the 

Door Center Panel (7A), stick the warning label to it.  

Install the Door Center Panel so that the warning label 

is easily readable from outside the greenhouse.

2.  The Roof Panels (2A) and the 

Roof Window Panel (4A) will need to be placed as 

shown in the illustrations below.  The bottom edges 

of these panels need to align above the gutter to 

direct rain off the greenhouse.  The top edges of 

these panels need to be placed up under the edge of 

the Crown (35) or the Window Support Beam (15).

3.  One at a time, place each Transparent Panel 

(1A through 9A) in its proper location on 

the Ceiling and Frame of the Greenhouse.  

Then, use Panel Clips (46) in the quantity 

and location of shown in Parts List A 

to secure the Transparent Panel in place.

4.  To attach Panel Clips,  

see illustration and instructions below:

A) 

Place the two loose ends of the Clip 

into the groove in the frame

B) 

Swing the center portion of the 

Clip up against the Panel

C) 

Two edges of the Clip swing under 

the edge of the panel and the center 

edge holds the panel in place.

Be careful, Panel Clip (46) ends may be sharp and may spring back!

Use and Maintenance

1. 

BEFORE EACH USE,

 inspect the general condition 

of the Greenhouse.  Check for loose screws, 

misalignment or binding of moving parts, cracked 

or broken parts, and any other condition that 

may affect the safe operation of the Greenhouse.  

If a problem occurs with the Greenhouse, have it 

corrected before further use.   

Do not use damaged equipment.

2. 

TO CLEAN

: Wipe with a damp cloth, using a mild 

detergent. 

Do not use cleaners that are combustible, 

corrosive, or not compatible with aluminum.

3. 

WHEN STORING

: Keep the Greenhouse 

in a box and in a clean, dry location.

SAFETY

FRAME

MAINTENANCE

FOUNDA

TION

Summary of Contents for 69714

















Reviews: