1.
2.
Slide open the cover. The GDK’s
keypad will illuminate.
Press the number 9 eight times, then
press ENTER, the GDK will beep
once and the green LED will
illuminate for two seconds followed
by two quick beeps. The GDK will
power OFF. This clears the GDK of
any previous passwords and
security codes so that you can
begin a new setup. Your GDK has
now ready to learn your new
password and garage door security
code(s).
NOTE: Use the reset code only to clear
the GDK of all passwords and garage door
security codes.
1. Select a PIN (Personal Identifica-
tion Number) and write it down.
This will be your password. Your
PIN can be up to 8 digits long.
Press the ENTER key to illuminate
the GDK’s keypad.
3.
Press tne number 1 (Factory
Default Password) followed by
ENTER. The green LED will blink
two times followed by one beep.
The GDK is now on and ready to
learn your new password (PIN).
Press STORE followed by the
PlN1, PIN2* or PIN3* key. The first
red LED, corresponding to PIN1,
will light and remain lit as the
green LED blinks.
*NOTE: The first time you enter a
password, GDK automatically defaults that
password to PIN1, even if PIN2 or PIN3 is
pressed.
5. PIN
Enter the PIN you wrote down in
STEP 1 then press ENTER. The
GDK will emit a double-ticking sound
to prompt you to confirm your new
PIN
password. Now reenter the PIN and
press ENTER again. If you entered
the same PIN correctly, the green
LED will illuminate for three seconds
followed by two beeps. The GDK will
then power OFF.
NOTE: If you make a mistake in entering
your PIN, press the EXIT key and return to
STEP 2 to re-enter your new PIN.
You will need your original garage door
opener when setting up GDK’s garage
door security code. Open your original
garage door opener so that you can view
the DIP switches.
1 .PlN
Open the GDK’s cover or, if the
cover is already open, press
ENTER. Key in your PIN followed
by ENTER. The GDK will beep and
the green light will blink twice if the
PIN is correctly entered. If you
enter your PIN incorrectly, the GDK
will beep and the red light will blink
once.
Press STORE followed by
DOOR1, DOOR2 or DOOR3. The
first six LEDs will chase. Enter the
number (1-6) from the table for
your brand of garage door
opener (See Figure 4). The
corresponding LED will light.
NOTE: If you make a mistake during the set
up p r o c e s s , press the EXIT key, re-enter your
PIN and return to step 1 in the "SETTlNG UP
THE SECURITY CODE TO OPERATE
YOUR GARAGE DOOR" section to re-enter
your garage door opener’s code.
I
MULTI-CODE
AMBASSADOR
MULTI EL MAC
MOORE-O-MATIC
LINEAR
DELTA
SHIMA
POWERLIFT
3
GENIE MODEL
AT90
GENIE MODEL
SD9500
LIFTADOOR
BLUE MAX
EZ LIFT
4
GENIE MODEL
AR85
5
CHAMBERLAIN
SEARS
RAYNOR
LIFT-MASTER
WAYNE DALTON
MASTER
MECHANIC
STANLEY
6
AUTOMATIC
DOORMAN
VEMCO
10 BITS/300 MHZ
8 BITS/310 MHZ
12 BITS/390 MHZ
9 BITS/390 MHZ
9 BITS/390 MHZ
TERTIARY BITS
10 BITS/31 0 MHZ
3. Press ENTER. All of the LEDs will
begin to chase, then the first LED
will blink.
Using the UP, MID and DOWN
keys, match the LEDs to the DIP
switches in your original garage
door opener. When you press UP,
the LED will remain on. When you
press MID, the LED will flash
slowly and when you press
DOWN, the LED will remain off.
NOTE: The LED s must match exactly to
the DIP switches on your original garage
door opener.