ON Semiconductor NCP1351 Series, User Manual

Page: 9 / 11

NCP1351PRINTGEVB
http://onsemi.com
9
Table 4. BILL OF MATERIAL FOR THE NCP1351 40 W PRINTER EVALUATION BOARD
(continued)
Designator
Lead
Free
Substitution
Allowed
Manufacturer
Part Number
Manufacturer Footprint Tolerance Value Description Qty.
R2 1 Resistor 4.7 M W /0.33 W 5% Axial − − Yes Yes
R5, R6 2 SMD Resistor
330k W /0.25 W
1% SOD − 1206 Vishay CRCW1206330RFKEA Yes Yes
R7 1 SMD Resistor 0 W /0.25 W 5% SOD − 1206 Vishay CRCW12060000Z0EA Yes Yes
R8, R19 2 SMD Resistor 2.7 k W /0.25 W 5% SOD − 1206 Vishay CRCW12062R70JNEA Yes Yes
R9, R12 2 SMD Resistor 0 W /0.25 W 5% SOD − 1206 Vishay CRCW12060000Z0EA Yes Yes
R10, R11,
R18
3 SMD Resistor 1 k W /0.25 W 5% SOD − 1206 Vishay CRCW12061K00JNEA Yes Yes
R13 1 SMD Resistor
3.4 k W /0.25 W
1% SOD − 1206 Vishay CRCW12063K40FKEA Yes Yes
R14 1 SMD Resistor 0.33 W /0.5 W 1% SOD − 1206 − − Yes Yes
R15 1 Resistor 150 k W /2 W 5% Axial − − Yes Yes
R20 1 SMD Resistor 100 k W /0.25 W 1% SOD − 1206 Vishay CRCW1206100KFKEA Yes Yes
R21 1 SMD Resistor 56 k W /0.25 W 1% SOD − 1206 Vishay CRCW120656K0FKEA Yes Yes
R22 1 SMD Resistor 10 k
W
/0.25 W 1% SOD − 1206 Vishay CRCW120610K0FKEA Yes Yes
R23, R24 2 SMD Resistor 3.3 M W /0.25 W 5% SOD − 1206 Vishay CRCW12063M30JNEA Yes Yes
R26 1 SMD Resistor 0 W /0.25 W 1% SOD − 1206 Vishay CRCW12060000FKEA Yes Yes
R28 1 SMD Resistor 8.2 k W /0.25 W 1% SOD − 1206 Vishay CRCW12068K20FKEA Yes Yes
R30 1 SMD Resistor
47 k W /0.25 W
1% SOD − 1206 Vishay CRCW120647K0FKEA Yes Yes
R31 1 SMD Resistor 180 k W /0.25 W 1% SOD − 1206 Vishay CRCW1206180KFKEA Yes Yes
TEST PROCEDURE
Figure 12. Test Procedure Schematic
AC Input
(85 − 265 Vac)
16 V Output
0 V
32 V Output
WARNING: Be careful when manipulating the boards in operation, lethal voltages up to 600 V are present on the primary side. An isolation
transformer is also recommended for safer manipulations.
Necessary Equipment
•
1 current limited 230 Vrms AC source (current limited
to avoid board destruction in case of a defective part)
•
1 DC volt-meter able to measure up to 50 V DC
•
2 programmable electronic loads
Test Procedure
1. Apply 110 Vac on the Vin pins. Output pins are
left floating.
2. Measure the output voltage between pins +16 V et
GND and b32 V and GND with a
volt-meter on the 50 V range. The measurements
should be respectively 16 and 32 volts (
± 10%).