background image

©

 Semiconductor Components Industries, LLC, 2013

February, 2013 

 Rev. 26

1

Publication Order Number:

CAT24C01/D

CAT24C01, CAT24C02,
CAT24C04, CAT24C08,
CAT24C16

1-Kb, 2-Kb, 4-Kb, 8-Kb and
16-Kb I

2

C CMOS Serial

EEPROM

Description

The CAT24C01/02/04/08/16 are 1

Kb, 2

Kb, 4

Kb, 8

Kb and

16

Kb respectively CMOS Serial EEPROM devices organized

internally as 8/16/32/64 and 128 pages respectively of 16 bytes each.
All devices support both the Standard (100 kHz) as well as Fast
(400 kHz) I

2

C protocol.

Data is written by providing a starting address, then loading 1 to 16

contiguous bytes into a Page Write Buffer, and then writing all data to
non

volatile memory in one internal write cycle. Data is read by

providing a starting address and then shifting out data serially while
automatically incrementing the internal address count.

External address pins make it possible to address up to eight

CAT24C01 or CAT24C02, four CAT24C04, two CAT24C08 and one
CAT24C16 device on the same bus.

Features

Supports Standard and Fast I

2

C Protocol

1.7 V to 5.5 V Supply Voltage Range

16

Byte Page Write Buffer

Hardware Write Protection for Entire Memory

Schmitt Triggers and Noise Suppression Filters on I

2

C Bus Inputs

(SCL and SDA)

Low power CMOS Technology

More than 1,000,000 Program/Erase Cycles

100 Year Data Retention

Industrial and Extended Temperature Range

These Devices are Pb

Free, Halogen Free/BFR Free and are RoHS

Compliant

SDA

SCL

WP

V

CC

V

SS

1
2
3
4

8

7
6
5

CAT24C__

16  /  08  /  04  /  02  /  01

NC /

/

/

/

NC NC

NC NC
NC

A

0

A

0

A

1

A

1

A

1

A

2

A

2

A

2

A

2

/

/

/

/

/

/

/

/

PIN CONFIGURATION

PDIP (L), SOIC (W), TSSOP (Y), MSOP (Z),

* The TDFN (VP2) package is not recommended for new designs.

TDFN, (VP2)*, UDFN

EP (HU4) (Top View)

See detailed ordering and shipping information in the package
dimensions section on page 19 of this data sheet.

ORDERING INFORMATION

http://onsemi.com

SOIC

8

W SUFFIX

CASE 751BD

TSOT

23

TD SUFFIX

CASE 419AE

PDIP

8

L SUFFIX

CASE 646AA

TSSOP

8

Y SUFFIX

CASE 948AL

MSOP

8

Z SUFFIX

CASE 846AD

TDFN

8*

VP2 SUFFIX

CASE 511AK

V

CC

WP

SDA

V

SS

SCL

1

2

3

5

4

TSOT

23 (TD), TSOP

5** (TS) (Top View)

PIN CONFIGURATIONS

UDFN8

EP

HU4 SUFFIX

CASE 517AZ

WLCSP

4***

C4A SUFFIX

CASE 567DC

WLCSP

5***

C5A SUFFIX

CASE 567DD

*** WLCSP are available for the CAT24C04,

   CAT24C08 and CAT24C16 only.

TOP MARKING FOR WLCSP

X = Specific Device

X =

 Code

4 = 24C04
8 = 24C08
6 = 24C16

Y = Production Year (Last Digit)
M = Production Month (1

9, O, N, D)

WLCSP

4

WLCSP

5

WLCSP

4***

WLCSP

5***

(Top Views)

WP

SCL

SDA

SCL

SDA

Pin 1

A

1

2

3

1

2

B

C

A

B

Pin 1

V

CC

V

SS

V

CC

V

SS

 

X

 

X

Y M

Y M

Pin 1

(Ball Down)

Pin 1

TSOP

5**

TS SUFFIX

CASE 483

** TSOP are available for the CAT24C02 only.

Summary of Contents for CAT24C01






















Reviews:

Related manuals for CAT24C01