Omron ZW-7000 Series User Manual Download Page 234

Page: 234 / 336

Setting Sensing

232

ZW-8000/7000/5000

User's Manual

Setting Exposure Time Control Mode

Setting Light Exposure Time Control Mode p.129

As an example, here is an explanation of the procedure for setting the exposure time control mode to "AUTO"

and control edge of light adjustment to "measurement area 1".

Operating procedure

Steps

Key operation

Display

Description

Press and hold the

key for two seconds or more to enter the

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Press the

keys to select “SENS” and press the

key.

Press the

keys to select “LIGHT” and press the

key.

Select the exposure time control mode.

AUTO: Automatic
MANUAL: Fixed

The current setting value is displayed on the sub-display.

Press

key to enter editing mode and the sub-display blinks.

In this example, select “AUTO” and press the

key.

Set the Control edge.
In this example, “ADJ.SUR” is displayed on the main display, and the
current setting value is displayed on the sub-display.

Press

key to enter the editing mode, and the sub-display

blinks.

To edit numerical values, use the

keys.

In this example, select “EDGE1” and press the

key.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands