manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 230

Functions and Operations during Measurement

228

ZW-8000/7000/5000 

User's Manual

Changing Threshold Values

The threshold value for the task displayed on the main display in the RUN mode can be changed. 

To change the target task, change the task displayed on the main display.

Changing Display Details p.227

As an example, here is an explanation of the procedure for setting the HIGH threshold value by entering 

“1.000” directly. 

Operating procedure

Steps

Key operation

Display

Description

1

Press the 

 key in the RUN mode to display the setting menu. 

2

Press the 

 / 

 key to select H.JUDGE, then press the 

 

key.

3

Set “1.000” as the HIGH threshold value. 
The current measured value is displayed on the main display and the 
current set threshold value is displayed on the sub-display. (At this 
time, the THRESHOLD-H indicator lights up.)

Press 

 key to enter the editing mode, and the sub-display 

blinks.

To edit numerical values, use the 

/

/

/

 keys.

Input “1.000”, then press the 

 key.

4

Press the 

 key to leave the setting menu. 

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands