Omron ZW-7000 Series User Manual Download Page 229

Page: 229 / 336

Functions and Operations during Measurement

ZW-8000/7000/5000
User's Manual

227

Senso

r con

trol
ler
ope

ons

Changing Display Details

The measurement result displayed on the main display in RUN mode can be selected from TASK1 to 4.

The number of digits displayed can also be changed.

As an example, here is an explanation of the procedure for setting TASK2 as the task to be displayed target.

Operating procedure

Setting [DISPLAY]

Option [DISPLAY]

Task for displayed target [DISP]

TASK1/TASK2/TASK3/TASK4

Decimal point digit [DEC.NUM]

0 [0DIG]/1 [1DIG]/2 [2DIG]/3 [3DIG]/4 [4DIG]/5 [5DIG]

Steps

Key operation

Display

Description

Press the

key in the RUN mode to display the setting menu.

Press the

keys to select “DISP” and press the

key.

Select the task to be the displayed target.
The current setting value is displayed on the sub-display.

Press

key to enter editing mode and the sub-display blinks.

Select “TASK2” and press the

key.

Press the

key to leave the setting menu.

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands