manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 206

Changing between Online and Offline

204

ZW-8000/7000/5000 

User's Manual

6-3 Changing between Online and Offline

Before you go offline, save all settings and parameter changes to the Sensor's internal memory. Saving your 

project does not save the data in the Sensor.

You can use the following two methods to change between offline and online.

 Multi View Explore

: [(Sensor Name)] (right click)| [Online]/[Offline]]

 Multi View Explore

: [Device group] | [(Sensor model)] (Double-click)

 

→

 Edit pane

: [Online] Icon | [Sensor connection] | [Connect] or [Disconnect]

When Sysmac Studio and the sensor controller bank mode (refer to 

Clearing the Bank Settings p.188) differ, the 

current bank number after project data synchronization is set to the initial value (1).

1

To go offline, click [Disconnect]. To go 

online, click [Connect].

2

When you click [Connect], the Sensor 

Controller with the specified IP address is 

connected. When the connection is 

successful, Sensor Controller information is 

displayed.

3

When you click [Connect], you must 

synchronize the data between the Sensor 

and the project.

When a project setting data is synchronized with 

Sensor Controller, select [Transfer to Sensor].

 

When synchronize a Sensor Controller's setting 

data with project, select [Transfer from Sensor].

Saving the Bank/System Settings p.185, p.263

 

Saving a project p.93

Note

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands