©
OMRON Corporation 2006-2015 All Rights Reserved.
Model
ZFV-LTF01
Smart Sensor
For Model ZFV-SC50
□
/90
□
EXTERNAL LIGHTING (BACK LIGHTING)
PRECAUTIONS FOR SAFE USE
(1) Installation Environment
･
Do not use the product in environments where it can
be exposed to inflammable / explosive gas.
･
To secure the safety of operation and maintenance, do
not install the product close to high-voltage devices
and power devices.
･
During installation, make sure that screws are
tightened firmly.
(3) Others
･
Moderate burn may possibly occur. Lightings is hot
immediately after power off. Do not touch it.
･
Do not attempt to dismantle, repair, or modify the
product.
･
Dispose of this product as industrial waste.
(2) Power Supply and Wiring
･
High-voltage lines and power lines must be wired
separately from this product. Wiring them together or
placing them in the same duct may cause induction,
resulting in malfunction or damage.
Please observe the following precautions for safe use of
the products.
PRECAUTIONS FOR CORRECT USE
Please observe the following precautions to prevent
failure to operate, malfunctions, or undesirable effects on
product performance.
･
Do not use thinner, benzene, acetone or kerosene to
clean the Sensor Head and Amplifier Unit.
･
To remove smaller dust particles, wipe gently with a
soft cloth. Do not use excessive force to wipe off dust
particles.
(2) Maintenance and Inspection
(1) Power Supply and Wiring
･
Before connecting/disconnecting the External
Lighting, make sure that the Smart Sensor is turned
OFF. The Smart Sensor may break down if the
External Lighting is connected or disconnected while
the power is ON.
･
Use only combinations of External Lightings and
Sensor Heads specified in this sheet.
Insert the External Lighting connector into the Extra Light
connector of the Sensor Head.
Connecting the Sensor Head
Dimensions
Item
Applicable sensor head
Lighting method
Lighting pulse width
Light Source
Power supply voltage
Current consumption
Dielectric strength
Vibration resistance
(destruction)
Shock resistance
(destruction)
Ambient temperature
Ambient humidity
Ambient atmosphere
Connection method
Degree of protection
Materials
Weight
ZFV-LTF01
ZFV-SC50/SC50W/SC90/SC90W
Pulse lighting
Fixed width (1.1~1.4ms)
Sixty white LEDs
48 VDC (Supplied from Sensor Head.)
Approx. 160 mA
1000 VAC, 50/60 Hz for 1 min
10 to 150 Hz, 0.35-mm single amplitude,
10 times each in X, Y, and Z directions for 8 min
150 m/s
2
, three times each in six directions
(up/down, left/right, forward/backward)
Operating: 0 to 40
℃
, Storage: -20 to 65
℃
(with no icing or condensation)
Operating and storage: 35% to 85%
(with no condensation)
Must be free of corrosive gas.
Prewired, Standard cable length: 2 m
IEC60529, IP20
SPCC
Approx. 500 g (550 g)
Specifications
74±0.1
74±0.1
( Unit : mm )
74
74
22
2000
＋
100
0
103
1
70
109
4-M3 depth 8
70
(Emitting Surface)
(Emitting Surface)
Mounting hole dimensions
FOCUS
LIGHT
Extra Light Connector
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
The following notice applies only to products that carry the CE mark:
Notice:
This is a class A product. In residential areas it may cause radio
interference, in which case the user may be required to take adequate
measures to reduce interference.
Manufacturer:
Omron Corporation,
Shiokoji Horikawa, Shimogyo-ku,
Kyoto 600-8530 JAPAN
TRACEABILITY INFORMATION:
Importer in EU:
Omron Europe B.V.
Wegalaan 67-69
2132 JD Hoofddorp,
The Netherlands
Suitability for Use
s
Omron Companies shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Product in the
Buyer’s application or use of the Product. At Buyer’s request, Omron will
provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in
combination with the end product, machine, system, or other application or
use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Oct, 2014
D
OMRON Corporation
Industrial Automation Company
Contact: www.ia.omron.com
Tokyo, JAPAN
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Regional Headquarters
