manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 223

BIOS - Chipset Details

This section provides BIOS Chipset details for 6

th

 generation and 7

th

 generation CPUs.

Memory Thermal Configuration

Provides BIOS Chipset details for the submenu Processor / Memory Configuration / Memory Ther-
mal Configuration /.

Changeable BIOS Memory Thermal Configuration parameters and their factory default values:

Item

Default / Remark

Memory Power and
Thermal Throttling

DDR PowerDown and idle counter

BIOS

For LPDDR Only: DDR PowerDown annd idle coun-
ter

BIOS

REFRESH_2X_MODE

Disabled

LPDDR Thermal Sensor

Enabled

SelfRefresh Enable

Enabled

SelfRefresh IdleTimer

512

Throttler CKEMin Defeature

Disabled

Throttler CKEMin Timer

48

For LPDDR Only: Throttler CKEMin Defeature 

*1

Enabled

For LPDDR Only: Throttler CKEMin Timer 

*1

64

DRAM Power Meter

Use user provided power
weights, scale factor, and
channel power floor val-
ues

Disabled

Memory Thermal Report-
ing

Lock Thermal Manage-
ment Registers

Enabled

Extern Therm Status

Disabled

Closed Loop Therm
Manage

Disabled

Open Loop Therm Man-
age

Disabled

Thermal Threshold Set-
tings

All settings = 255

Thermal Throttle Budget
Settings

All settings = 255

Memory RAPL

RAPL PL Lock

Disabled

RAPL PL 1 enable

Disabled

RAPL PL 1 Power

0

RAPL PL 1 WindowX

0

RAPL PL 1 WindowY

0

RAPL PL 2 enable

Disabled

RAPL PL 2 Power

222

RAPL PL 2 WindowX

1

RAPL PL 2 WindowY

10

Memory Thermal Management

Disabled

*1.

Available for 7

th

 generation CPUs.

Not available for 6

th

 generation CPUs.

Appendices

A-25

NY-series Industrial Box PC Hardware User's Manual (W553)

A-1 BIOS

A

A-1-3 BIOS for 6

th

 generation CPUs

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands