![background image](http://html1.mh-extra.com/html/omron/q2v-series/q2v-series_technical-manual_743226554.webp)
554
SIEPCYEUOQ2V01A Q2V Technical Manual
Note:
•
Set
F6-15 = 0, 1
to reload
F6-xx
,
F7-xx
.
•
Set
F6-15 = 0, 1
to reset the display on the keypad to
0
.
0 : Reload@Next Power Cycle
Restart the drive to update parameters.
1 : Reload Now
The changed parameters are updated without restarting the drive.
2 : Cancel Reload Request
Cancels
CyPo [Cycle Power to Accept Changes]
.
■
F6-16: Gateway Mode
No.
(Hex.)
Name
Description
Default
(Range)
F6-16
(0B8A)
Gateway Mode
Sets the gateway mode operation and the number of connected slave drives.
0
(0 to 4)
0 : Disabled
1 : 1 Slave Drive
2 : 2 Slave Drives
3 : 3 Slave Drives
4 : 4 Slave Drives
■
F6-20: MLII Address
No.
(Hex.)
Name
Description
Default
(Range)
F6-20
(036B)
MLII Address
Sets the station address for MECHATROLINK communication. Change the parameter then cycle
power on the drive.
0021h
(MECHATROLINK-II:
0020h - 003Fh,
MECHATROLINK-III:
0003h - 00EFh)
Note:
•
The setting range changes if using MECHATROLINK-II or MECHATROLINK-III:
–
MECHATROLINK-II (SI-T3) range: 20 to 3F
–
MECHATROLINK-III (SI-ET3) range: 03 to EF
•
Be sure to set a node address that is different than all other node addresses. Incorrect parameter settings will cause
AEr [Station
Address Setting Error]
errors and the L.ERR LED on the option will come on.
•
The drive detects
AEr
errors when the station address is 20 or 3F.
■
F6-21: MLII Frame Size
No.
(Hex.)
Name
Description
Default
(Range)
F6-21
(036C)
MLII Frame Size
Sets the frame size for MECHATROLINK communication. Restart the drive after you change the
parameter setting.
0
(0, 1)
0 : 32-byte
1 : 17-byte
■
F6-22: MLII Link Speed
No.
(Hex.)
Name
Description
Default
(Range)
F6-22
(036D)
MLII Link Speed
Sets the communications speed for MECHATROLINK-II. Restart the drive after you change the
parameter setting.
0
(0, 1)
Note:
This parameter is only available with the MECHATROLINK-II option.
0 : 10 Mbps
1 : 4 Mbps
V/f
OLV
OLV/PM
OLV/PM AOLV/PM
EZOLV
V/f
OLV
OLV/PM
OLV/PM AOLV/PM
EZOLV
V/f
OLV
OLV/PM
OLV/PM AOLV/PM
EZOLV
V/f
OLV
OLV/PM
OLV/PM AOLV/PM
EZOLV
Summary of Contents for Q2V Series
